欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD813212JIT
廠商: 意法半導體
英文描述: Flash In-System Programmable ISP Peripherals For 8-bit MCUs
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 10/110頁
文件大小: 1737K
代理商: PSD813212JIT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
10/110
PIN DESCRIPTION
Table 2. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
ADIO0-7
30-37
I/O
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
If your MCU does not have a multiplexed address/data bus, or you are using an 80C251
in page mode, connect A0-A7 to this port.
If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
ADIO8-15
39-46
I/O
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.
If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
CNTL0
47
I
The following control signals can be connected to this port, based on your MCU:
WR – active Low Write Strobe input.
R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL1
50
I
The following control signals can be connected to this port, based on your MCU:
RD – active Low Read Strobe input.
E – E clock input.
DS – active Low Data Strobe input.
PSEN – connect PSEN to this port when it is being used as an active Low READ signal.
For example, when the 80C251 outputs more than 16 address bits, PSEN is actually the
READ signal.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL2
49
I
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
相關PDF資料
PDF描述
PSD813220JIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813270JIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD953212JIT High Speed CMOS Logic Quad 2-Input NAND Gates 14-SOIC -55 to 125
PSD953212JT High Speed CMOS Logic Quad 2-Input NAND Gates 14-SOIC -55 to 125
PSD953212MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
相關代理商/技術參數
參數描述
PSD813212JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813212MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813212MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813215JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813215JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 囊谦县| 桐城市| 民和| 吉隆县| 天镇县| 额尔古纳市| 东乌珠穆沁旗| 肇源县| 青岛市| 吴忠市| 呼图壁县| 屏东市| 休宁县| 肥东县| 灌阳县| 攀枝花市| 阜新市| 吴江市| 清水河县| 和平区| 蓬莱市| 盐源县| 鄂伦春自治旗| 宣化县| 清新县| 浙江省| 凤城市| 闽侯县| 仁化县| 行唐县| 合江县| 枣庄市| 特克斯县| 百色市| 东宁县| 石渠县| 高邑县| 乌拉特中旗| 二手房| 昌乐县| 汝城县|