欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD813F2V-12
廠商: 意法半導體
英文描述: Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
中文描述: Flash在系統可編程(ISP)的周邊8位MCU,5V的
文件頁數: 10/110頁
文件大小: 1737K
代理商: PSD813F2V-12
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
10/110
PIN DESCRIPTION
Table 2. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
ADIO0-7
30-37
I/O
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
If your MCU does not have a multiplexed address/data bus, or you are using an 80C251
in page mode, connect A0-A7 to this port.
If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
ADIO8-15
39-46
I/O
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.
If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
CNTL0
47
I
The following control signals can be connected to this port, based on your MCU:
WR – active Low Write Strobe input.
R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL1
50
I
The following control signals can be connected to this port, based on your MCU:
RD – active Low Read Strobe input.
E – E clock input.
DS – active Low Data Strobe input.
PSEN – connect PSEN to this port when it is being used as an active Low READ signal.
For example, when the 80C251 outputs more than 16 address bits, PSEN is actually the
READ signal.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL2
49
I
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
相關PDF資料
PDF描述
PSD834F2V-12 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD854F2V-12 CONN HEADER 28POS .100 STR GOLD
PSD834F5V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD854F5V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD814F5V-90 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
相關代理商/技術參數
參數描述
PSD813F2V-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2V-12J1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash in-system programmable (ISP) peripherals for 8-bit MCUs, 3.3 V
PSD813F2V-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2V-12JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2V-12JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 舒兰市| 邳州市| 方城县| 齐河县| 吉木乃县| 滨海县| 治多县| 子长县| 汶川县| 惠安县| 读书| 谢通门县| 平舆县| 南和县| 田东县| 启东市| 自治县| 凤冈县| 延吉市| 丹江口市| 论坛| 邯郸市| 洪泽县| 武川县| 汉川市| 万安县| 永州市| 增城市| 于都县| 封丘县| 友谊县| 杂多县| 玉门市| 布尔津县| 长寿区| 雷州市| 辽源市| 保靖县| 繁峙县| 深圳市| 根河市|