欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD854F4V-20
廠商: 意法半導體
英文描述: Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
中文描述: Flash在系統可編程(ISP)的周邊8位MCU,5V的
文件頁數: 10/110頁
文件大小: 1737K
代理商: PSD854F4V-20
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
10/110
PIN DESCRIPTION
Table 2. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
ADIO0-7
30-37
I/O
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
If your MCU does not have a multiplexed address/data bus, or you are using an 80C251
in page mode, connect A0-A7 to this port.
If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
ADIO8-15
39-46
I/O
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.
If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
CNTL0
47
I
The following control signals can be connected to this port, based on your MCU:
WR – active Low Write Strobe input.
R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL1
50
I
The following control signals can be connected to this port, based on your MCU:
RD – active Low Read Strobe input.
E – E clock input.
DS – active Low Data Strobe input.
PSEN – connect PSEN to this port when it is being used as an active Low READ signal.
For example, when the 80C251 outputs more than 16 address bits, PSEN is actually the
READ signal.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL2
49
I
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
相關PDF資料
PDF描述
PSD814F4V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD834F4V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD854F4V-70 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD814F4V-90 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD834F5V-20 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
相關代理商/技術參數
參數描述
PSD-8M-01 制造商:Richco 功能描述:CB SPT REST MNT NAT 8MM SPC
PSD913212JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913212JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913212MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913212MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 永康市| 凭祥市| 和顺县| 会同县| 台中市| 嘉兴市| 遂昌县| 安康市| 谷城县| 资中县| 宁国市| 德庆县| 高邑县| 民权县| 绥江县| 舒兰市| 枣强县| 乌鲁木齐市| 洞口县| 广平县| 泰州市| 会宁县| 宁夏| 贞丰县| 固镇县| 读书| 丹巴县| 密云县| 兴文县| 泸州市| 余干县| 廉江市| 容城县| 塔城市| 博野县| 大竹县| 尤溪县| 措美县| 班玛县| 鄂托克前旗| 渝北区|