欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD913320JT
廠商: 意法半導體
英文描述: TTL, NMOS To PECL Trans; Package: SOEIAJ-20; No of Pins: 20; Container: Tape and Reel; Qty per Container: 2000
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 64/110頁
文件大小: 1737K
代理商: PSD913320JT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
64/110
For Users of the HC11 (or compatible)
The HC11 turns off its E clock when it sleeps.
Therefore, if you are using an HC11 (or compati-
ble) in your design, and you wish to use the Pow-
er-down mode, you must not connect the E clock
to CLKIN (PD1). You should instead connect a
crystal oscillator to CLKIN (PD1). The crystal oscil-
lator frequency must be
less than
15 times the fre-
quency of AS. The reason for this is that if the
frequency is greater than 15 times the frequency
of AS, the PSD keeps going into Power-down
mode.
Other Power Saving Options
The PSD offers other reduced power saving op-
tions that are independent of the Power-down
mode. Except for the SRAM Stand-by and PSD
Chip Select Input (CSI, PD2) features, they are en-
abled by setting bits in PMMR0 and PMMR2.
Figure 33. Enable Power-down Flow Chart
PLD Power Management
The power and speed of the PLDs are controlled
by the Turbo Bit (Bit 3) in PMMR0. By setting the
bit to '1,' the Turbo mode is off and the PLDs con-
sume the specified stand-by current when the in-
puts are not switching for an extended time of
70ns. The propagation delay time is increased by
10ns after the Turbo Bit is set to '1' (turned off)
when the inputs change at a composite frequency
of less than 15 MHz. When the Turbo Bit is reset
to '0' (turned on), the PLDs run at full power and
speed. The Turbo Bit affects the PLD’s DC power,
AC power, and propagation delay.
Blocking MCU control signals with the bits of
PMMR2 can further reduce PLD AC power con-
sumption.
SRAM Standby Mode (Battery Backup).
The
PSD supports a battery backup mode in which the
contents of the SRAM are retained in the event of
a power loss. The SRAM has Voltage Stand-by
(V
STBY
, PC2) that can be connected to an external
battery. When V
CC
becomes lower than V
STBY
then the PSD automatically connects to Voltage
Stand-by (V
STBY
, PC2) as a power source to the
SRAM. The SRAM Standby Current (I
STBY
) is typ-
ically 0.5μA. The SRAM data retention voltage is
2V minimum. The Battery-on Indicator (VBATON)
can be routed to PC4. This signal indicates when
the V
CC
has dropped below V
STBY
.
Enable APD
Set PMMR0 Bit 1 = 1
PSD in Power
Down Mode
ALE/AS idle
for 15 CLKIN
clocks
RESET
Yes
No
OPTIONAL
Disable desired inputs to PLD
by setting PMMR0 bits 4 and 5
and PMMR2 bits 2 through 6.
AI02892
相關PDF資料
PDF描述
PSD913320MIT BBG ECL TRNSLATR QUAD; Package: SOEIAJ-20; No of Pins: 20; Container: Tape and Reel; Qty per Container: 2000
PSD913320MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913370JIT TTL, NMOS To PECL Trans; Package: 20 LEAD PDIP; No of Pins: 20; Container: Rail; Qty per Container: 18
PSD913370JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913370MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
相關代理商/技術參數
參數描述
PSD913320MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913320MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913370JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913370JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD913370MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 保德县| 呼伦贝尔市| 平利县| 弋阳县| 昌图县| 莱阳市| 万年县| 盱眙县| 铁岭县| 平凉市| 余姚市| 韶山市| 兰西县| 沽源县| 大同县| 新竹市| 阳山县| 乌拉特前旗| 张掖市| 合水县| 巴林左旗| 宿松县| 武穴市| 融水| 灵武市| 兴山县| 湘阴县| 乐亭县| 馆陶县| 屏东县| 晋城| 旺苍县| 桦川县| 塔河县| 肥乡县| 西林县| 山阴县| 阆中市| 新巴尔虎左旗| 清丰县| 株洲县|