欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD9135V12MT
廠商: 意法半導體
英文描述: Flash In-System Programmable ISP Peripherals For 8-bit MCUs
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 10/110頁
文件大小: 1737K
代理商: PSD9135V12MT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
10/110
PIN DESCRIPTION
Table 2. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
ADIO0-7
30-37
I/O
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
If your MCU does not have a multiplexed address/data bus, or you are using an 80C251
in page mode, connect A0-A7 to this port.
If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
ADIO8-15
39-46
I/O
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.
If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
CNTL0
47
I
The following control signals can be connected to this port, based on your MCU:
WR – active Low Write Strobe input.
R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL1
50
I
The following control signals can be connected to this port, based on your MCU:
RD – active Low Read Strobe input.
E – E clock input.
DS – active Low Data Strobe input.
PSEN – connect PSEN to this port when it is being used as an active Low READ signal.
For example, when the 80C251 outputs more than 16 address bits, PSEN is actually the
READ signal.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL2
49
I
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
相關PDF資料
PDF描述
PSD8335V12MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9335V12MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD8133V12JIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9133V12JIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F3-70 RECTIFIER SCHOTTKY SINGLE 5A 30V 175A-Ifsm 0.55Vf 0.5A-IR SMC 3K/REEL
相關代理商/技術參數
參數描述
PSD9135V15JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9135V15JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9135V15MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9135V15MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9135V20JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
主站蜘蛛池模板: 平舆县| 龙州县| 贺兰县| 金乡县| 德令哈市| 诏安县| 南溪县| 田东县| 昌吉市| 铜川市| 临潭县| 深水埗区| 舟山市| 岫岩| 会理县| 南康市| 禹州市| 汉阴县| 石泉县| 思茅市| 竹溪县| 松潘县| 平潭县| 城口县| 游戏| 宕昌县| 韶关市| 宣恩县| 南阳市| 凭祥市| 汽车| 南宫市| 淮北市| 金溪县| 金门县| 桂阳县| 阿鲁科尔沁旗| 平谷区| 井冈山市| 唐山市| 华亭县|