欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD9142V12MT
廠商: 意法半導體
英文描述: Flash In-System Programmable ISP Peripherals For 8-bit MCUs
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 58/110頁
文件大小: 1737K
代理商: PSD9142V12MT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
58/110
Input Macrocells (IMC)
The Input Macrocells (IMC) can be used to latch or
store external inputs. The outputs of the Input
Macrocells (IMC) are routed to the PLD input bus,
and can be read by the MCU. See the section en-
titled
PLDS, page 33
.
Enable Out
The Enable Out register can be read by the MCU.
It contains the output enable values for a given
port. A 1 indicates the driver is in output mode. A
0 indicates the driver is in tri-state and the pin is in
input mode.
Ports A and B – Functionality and Structure
Ports A and B have similar functionality and struc-
ture, as shown in Figure
28
. The two ports can be
configured to perform one or more of the following
functions:
MCU I/O Mode
CPLD Output – Macrocells McellAB7-
McellAB0 can be connected to Port A or Port
B. McellBC7-McellBC0 can be connected to
Port B or Port C.
CPLD Input – Via the Input Macrocells (IMC).
Latched Address output – Provide latched
address output as per
Table 21., page 54
.
Address In – Additional high address inputs
using the Input Macrocells (IMC).
Open Drain/Slew Rate – pins PA3-PA0 and
PB3-PB0 can be configured to fast slew rate,
pins PA7-PA4 and PB7-PB4 can be
configured to Open Drain Mode.
Data Port – Port A to D7-D0 for 8 bit non-
multiplexed bus
Multiplexed Address/Data port for certain
types of MCU bus interfaces.
Peripheral Mode – Port A only
Figure 28. Port A and Port B Structure
I
DAREG.
D
Q
D
G
Q
D
Q
D
Q
WR
WR
WR
ADDRESS
MACROCELL OUTPUTS
ENABLE PRODUCT TERM (.OE)
ALE
READ MUX
P
D
B
CPLD-INPUT
CONTROL REG.
DIR REG.
INPUT
MACROCELL
ENABLE OUT
DATA IN
OUTPUT
OMUX
A PORT
DATA OUT
ADDRESS
A[7:0] OR A[15:8]
AI02887
相關PDF資料
PDF描述
PSD8342V12MT OSC 5V 8PIN CMOS
PSD8543V12JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9543V12JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD8143V12MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9143V12MIT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
相關代理商/技術參數
參數描述
PSD934F2-15J 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F290J 制造商:WSI 功能描述:
PSD934F2-90J 功能描述:SPLD - 簡單可編程邏輯器件 PLCC-52 5V 2M 90NS RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2V-15J 功能描述:SPLD - 簡單可編程邏輯器件 3.3V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
主站蜘蛛池模板: 会东县| 金昌市| 分宜县| 徐州市| 营山县| 蓬溪县| 江都市| 呼伦贝尔市| 崇文区| 讷河市| 麟游县| 凤翔县| 舒兰市| 昂仁县| 莱阳市| 正定县| 凤凰县| 汪清县| 新干县| 米脂县| 宁河县| 周宁县| 辰溪县| 丰原市| 和龙市| 曲沃县| 邳州市| 朔州市| 临高县| 遵义市| 芦山县| 策勒县| 云南省| 保靖县| 霍林郭勒市| 调兵山市| 德保县| 无为县| 库伦旗| 安陆市| 宿松县|