欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD914590JIT
廠商: 意法半導體
英文描述: Low-Power BiCMOS Current-Mode PWM 8-TSSOP -40 to 85
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 58/110頁
文件大小: 1737K
代理商: PSD914590JIT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
58/110
Input Macrocells (IMC)
The Input Macrocells (IMC) can be used to latch or
store external inputs. The outputs of the Input
Macrocells (IMC) are routed to the PLD input bus,
and can be read by the MCU. See the section en-
titled
PLDS, page 33
.
Enable Out
The Enable Out register can be read by the MCU.
It contains the output enable values for a given
port. A 1 indicates the driver is in output mode. A
0 indicates the driver is in tri-state and the pin is in
input mode.
Ports A and B – Functionality and Structure
Ports A and B have similar functionality and struc-
ture, as shown in Figure
28
. The two ports can be
configured to perform one or more of the following
functions:
MCU I/O Mode
CPLD Output – Macrocells McellAB7-
McellAB0 can be connected to Port A or Port
B. McellBC7-McellBC0 can be connected to
Port B or Port C.
CPLD Input – Via the Input Macrocells (IMC).
Latched Address output – Provide latched
address output as per
Table 21., page 54
.
Address In – Additional high address inputs
using the Input Macrocells (IMC).
Open Drain/Slew Rate – pins PA3-PA0 and
PB3-PB0 can be configured to fast slew rate,
pins PA7-PA4 and PB7-PB4 can be
configured to Open Drain Mode.
Data Port – Port A to D7-D0 for 8 bit non-
multiplexed bus
Multiplexed Address/Data port for certain
types of MCU bus interfaces.
Peripheral Mode – Port A only
Figure 28. Port A and Port B Structure
I
DAREG.
D
Q
D
G
Q
D
Q
D
Q
WR
WR
WR
ADDRESS
MACROCELL OUTPUTS
ENABLE PRODUCT TERM (.OE)
ALE
READ MUX
P
D
B
CPLD-INPUT
CONTROL REG.
DIR REG.
INPUT
MACROCELL
ENABLE OUT
DATA IN
OUTPUT
OMUX
A PORT
DATA OUT
ADDRESS
A[7:0] OR A[15:8]
AI02887
相關PDF資料
PDF描述
PSD9332V70MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9332V90MIT Low Power, Dual Output, Current Mode PWM Controller 16-SOIC -40 to 85
PSD9332V90MT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD933320JIT Low Power, Dual Output, Current Mode PWM Controller 16-SSOP/QSOP -40 to 85
PSD933320JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
相關代理商/技術參數
參數描述
PSD934F2-15J 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F290J 制造商:WSI 功能描述:
PSD934F2-90J 功能描述:SPLD - 簡單可編程邏輯器件 PLCC-52 5V 2M 90NS RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2V-15J 功能描述:SPLD - 簡單可編程邏輯器件 3.3V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
主站蜘蛛池模板: 前郭尔| 新晃| 沿河| 天长市| 铜陵市| 金秀| 三江| 永康市| 定边县| 新沂市| 松阳县| 耿马| 瓦房店市| 聊城市| 清远市| 正镶白旗| 互助| 保山市| 吉水县| 浏阳市| 招远市| 玛纳斯县| 浮山县| 娄烦县| 紫金县| 卓资县| 耒阳市| 永嘉县| 依安县| 泌阳县| 洪湖市| 宝鸡市| 铜山县| 出国| 武城县| 永嘉县| 太原市| 安徽省| 广饶县| 西峡县| 南城县|