欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: PSD9333V70JT
廠商: 意法半導體
英文描述: Flash In-System Programmable ISP Peripherals For 8-bit MCUs
中文描述: Flash在系統可編程ISP的外設的8位微控制器
文件頁數: 58/110頁
文件大小: 1737K
代理商: PSD9333V70JT
PSD813F2, PSD833F2, PSD834F2, PSD853F2, PSD854F2
58/110
Input Macrocells (IMC)
The Input Macrocells (IMC) can be used to latch or
store external inputs. The outputs of the Input
Macrocells (IMC) are routed to the PLD input bus,
and can be read by the MCU. See the section en-
titled
PLDS, page 33
.
Enable Out
The Enable Out register can be read by the MCU.
It contains the output enable values for a given
port. A 1 indicates the driver is in output mode. A
0 indicates the driver is in tri-state and the pin is in
input mode.
Ports A and B – Functionality and Structure
Ports A and B have similar functionality and struc-
ture, as shown in Figure
28
. The two ports can be
configured to perform one or more of the following
functions:
MCU I/O Mode
CPLD Output – Macrocells McellAB7-
McellAB0 can be connected to Port A or Port
B. McellBC7-McellBC0 can be connected to
Port B or Port C.
CPLD Input – Via the Input Macrocells (IMC).
Latched Address output – Provide latched
address output as per
Table 21., page 54
.
Address In – Additional high address inputs
using the Input Macrocells (IMC).
Open Drain/Slew Rate – pins PA3-PA0 and
PB3-PB0 can be configured to fast slew rate,
pins PA7-PA4 and PB7-PB4 can be
configured to Open Drain Mode.
Data Port – Port A to D7-D0 for 8 bit non-
multiplexed bus
Multiplexed Address/Data port for certain
types of MCU bus interfaces.
Peripheral Mode – Port A only
Figure 28. Port A and Port B Structure
I
DAREG.
D
Q
D
G
Q
D
Q
D
Q
WR
WR
WR
ADDRESS
MACROCELL OUTPUTS
ENABLE PRODUCT TERM (.OE)
ALE
READ MUX
P
D
B
CPLD-INPUT
CONTROL REG.
DIR REG.
INPUT
MACROCELL
ENABLE OUT
DATA IN
OUTPUT
OMUX
A PORT
DATA OUT
ADDRESS
A[7:0] OR A[15:8]
AI02887
相關PDF資料
PDF描述
PSD8533V70JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9533V70JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD8143V70JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD9143V70JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD8343V70JT Flash In-System Programmable ISP Peripherals For 8-bit MCUs
相關代理商/技術參數
參數描述
PSD934F2-15J 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F290J 制造商:WSI 功能描述:
PSD934F2-90J 功能描述:SPLD - 簡單可編程邏輯器件 PLCC-52 5V 2M 90NS RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 5V 2M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD934F2V-15J 功能描述:SPLD - 簡單可編程邏輯器件 3.3V 2M 150ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
主站蜘蛛池模板: 张家界市| 调兵山市| 江安县| 喀喇沁旗| 武安市| 林芝县| 湛江市| 文成县| 承德市| 台中市| 隆回县| 宁蒗| 霍山县| 晋中市| 灵璧县| 青海省| 通道| 洪洞县| 台湾省| 北碚区| 息烽县| 儋州市| 河曲县| 岳池县| 嘉禾县| 威远县| 长白| 灵石县| 大石桥市| 吉安市| 屏南县| 穆棱市| 乌兰察布市| 平遥县| 东乡族自治县| 虎林市| 宁德市| 保德县| 东台市| 雷山县| 云林县|