欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: Q67100-Q2080
廠商: SIEMENS AG
英文描述: 16M x 72-Bit Dynamic RAM Module
中文描述: 16米x 72位動態隨機存儲器模塊
文件頁數: 13/53頁
文件大?。?/td> 418K
代理商: Q67100-Q2080
HYB 39S64400/800/160BT(L)
64-MBit Synchronous DRAM
Data Book
13
12.99
command is necessary. A minimum
t
RC
time is required between two automatic refreshes in a burst
refresh mode. The same rule applies to any access command after the automatic refresh operation.
The chip has an on-chip timer and the Self Refresh mode is available. It enters the mode when RAS,
CAS, and CKE are low and WE is high at a clock timing. All of external control signals including the
clock are disabled. Returning CKE to high enables the clock and initiates the refresh exit operation.
After the exit command, at least one
t
RC
delay is required prior to any access command.
DQM Function
DQM has two functions for data I/O read and write operations. During reads, when it turns to “high”
at a clock timing, data outputs are disabled and become high impedance after two clock delay (DQM
Data Disable Latency
t
DQZ
). It also provides a data mask function for writes. When DQM is activated,
the write operation at the next clock is prohibited (DQM Write Mask Latency
t
DQW
= zero clocks).
Suspend Mode
During normal access mode, CKE is held high enabling the clock. When CKE is low, it freezes the
internal clock and extends data read and write operations. One clock delay is required for mode
entry and exit (Clock Suspend Latency
t
CSL
).
Power Down
In order to reduce standby power consumption, a power down mode is available. All banks must be
precharged and the necessary Precharge delay (
t
RP
) must occur before the SDRAM can enter the
Power Down mode. Once the Power Down mode is initiated by holding CKE low, all of the receiver
circuits except CLK and CKE are gated off. The Power Down mode does not perform any refresh
operations, therefore the device can’t remain in Power Down mode longer than the Refresh period
(
t
REF
) of the device. Exit from this mode is performed by taking CKE “high”. One clock delay is
required for mode entry and exit.
Auto Precharge
Two methods are available to precharge SDRAMs. In an automatic precharge mode, the CAS
timing accepts one extra address, CA10, to determine whether the chip restores or not after the
operation. If CA10 is high when a Read Command is issued, the
Read with Auto-Precharge
function is initiated. If CA10 is high when a Write Command is issued, the
Write with Auto-
Precharge
function is initiated. The SDRAM automatically enters the precharge operation two
clocks after the last data in.
Precharge Command
There is also a separate precharge command available. When RAS and WE are low and CAS is
high at a clock timing, it triggers the precharge operation. Three address bits, BA0, BA1 and A10 are
used to define banks as shown in the following list. The precharge command can be imposed one
clock before the last data out for CAS latency = 2 and two clocks before the last data out for CAS
latency = 3. Writes require a time delay
t
WR
from the last data out to apply the precharge command.
相關PDF資料
PDF描述
Q67100-Q2085 8M x 72-Bit Dynamic RAM Module
Q67100-Q2086 8M x 72-Bit Dynamic RAM Module
Q67100-Q2096 4M x 32-Bit EDO-DRAM Module
Q67100-Q2098 8M x 32-Bit EDO-DRAM Module
Q67100-Q2099 8M x 32-Bit EDO-DRAM Module
相關代理商/技術參數
參數描述
Q67100-Q2085 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8M x 72-Bit Dynamic RAM Module
Q67100-Q2086 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8M x 72-Bit Dynamic RAM Module
Q67100-Q2096 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:4M x 32-Bit EDO-DRAM Module
Q67100-Q2098 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8M x 32-Bit EDO-DRAM Module
Q67100-Q2099 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8M x 32-Bit EDO-DRAM Module
主站蜘蛛池模板: 隆安县| 若羌县| 泾阳县| 恩平市| 连南| 黔西| 河间市| 姜堰市| 库伦旗| 开远市| 彰化市| 龙岩市| 永清县| 桐乡市| 广汉市| 灌云县| 全州县| 鄯善县| 西丰县| 昌邑市| 新田县| 和田县| 沙河市| 曲阜市| 凤山县| 乐都县| 平谷区| 正定县| 五家渠市| 历史| 英吉沙县| 昌宁县| 和平县| 桦川县| 栾城县| 天全县| 南京市| 满城县| 长垣县| 行唐县| 辉县市|