- 您現在的位置：買賣IC網 > PDF目錄69310 > R5F2138CGKFP FLASH, 20 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | R5F2138CGKFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件頁數： | 1/30頁 |
| 文件大小： | 483K |
| 代理商： | R5F2138CGKFP |
當前第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
59
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
Bit 5 – PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin change interrupt 1 is
enabled. Any change on any enabled PCINT15...8 pin will cause an interrupt. The corresponding interrupt of Pin
Change Interrupt Request is executed from the PCI1 Interrupt Vector. PCINT15:8 pins are enabled individually by
the PCMSK1 Register.
Bit 4 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin change interrupt 0 is
enabled. Any change on any enabled PCINT7...0 pin will cause an interrupt. The corresponding interrupt of Pin
Change Interrupt Request is executed from the PCI0 Interrupt Vector. PCINT7:0 pins are enabled individually by
the PCMSK0 Register.
Bit 0 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is
enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the External Interrupt Control Register A
(EICRA) define whether the external interrupt is activated on rising and/or falling edge of the INT0 pin or level
sensed. Activity on the pin will cause an interrupt request even if INT0 is configured as an output. The correspond-
ing interrupt of External Interrupt Request 0 is executed from the INT0 Interrupt Vector.
13.2.3
EIFR – External Interrupt Flag Register
Bit 7 – PCIF3: Pin Change Interrupt Flag 3
When a logic change on any PCINT30:24 pin triggers an interrupt request, PCIF3 becomes set (one). If the I-bit in
SREG and the PCIE3 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Note:
1. This bit is a reserved bit in Atmel
ATmega165A/ATmega165PA/ATmega325A/ATmega325PA/ATmega645A/ATmega645P and should always be writ-
ten to zero.
Bit 6 – PCIF2: Pin Change Interrupt Flag 2
When a logic change on any PCINT24:16 pin triggers an interrupt request, PCIF2 becomes set (one). If the I-bit in
SREG and the PCIE2 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Note:
1. This bit is a reserved bit in Atmel
ATmega165A/ATmega165PA/ATmega325A/ATmega325PA/ATmega645A/ATmega645P and should always be writ-
ten to zero.
Bit 5 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set (one). If the I-bit in
SREG and the PCIE1 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Bit 4 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set (one). If the I-bit in
SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the corresponding Interrupt Vector. The flag
is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
Bit
76543210
0x1C (0x3C)
PCIF3
PCIF2
PCIF1
PCIF0
–
INTF0
EIFR
Read/Write
R/W
RRR
R/W
Initial Value
00000000
相關PDF資料 |
PDF描述 |
|---|---|
| R5F21388HKFP | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2138AFKFP | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2138AHJFP | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2138CFJFP | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2138CHJFP | FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F2138CMDFD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:The R8C/38M Group has data flash (1 KB × 4 blocks) with the background operation |
| R5F2138CMDFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:The R8C/38M Group has data flash (1 KB × 4 blocks) with the background operation |
| R5F2138CMDFP#30 | 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 128KB FLASH 80LQFP |
| R5F2138CMDFP#V0 | 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 128KB FLASH 80LQFP |
| R5F2138CMDXXXFD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:The R8C/38M Group has data flash (1 KB × 4 blocks) with the background operation |
發布緊急采購，3分鐘左右您將得到回復。