- 您現在的位置：買賣IC網 > PDF目錄26851 > S201DH2 (SHARP ELECTRONICS CORP) TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX PDF資料下載
參數資料
| 型號： | S201DH2 |
| 廠商： | SHARP ELECTRONICS CORP |
| 元件分類： | 繼電器，輸入/輸出模塊 |
| 英文描述： | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 244K |
| 代理商： | S201DH2 |
8
S101DH2 Series
S201DH2 Series
■ Design Considerations
Sheet No.: D4-A01301EN
● Design guide
In order for the SSR to turn off, the triggering current (IF) must be 0.1mA or less.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs=0.022F and Rs=47. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
● Recommended Operating Conditions
Parameter
Symbol
Unit
Input
Output
Input signal current at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
IF(ON)
IF(OFF)
VOUT(rms)
IOUT(rms)
f
Topr
mA
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=0.022F, Rs=47)
Conditions
20
0
50
20
25
0.1
120
240
IT(rms)
×80%()
60
80
MIN.
MAX.
() See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
S101DH2
S201DH2
相關PDF資料 |
PDF描述 |
|---|---|
| S202SE1 | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| S206CPW7-6VF-BP | SINGLE COLOR DISPLAY CLUSTER, WHITE, 5 mm |
| S206CUB500-14VAC-P | SINGLE COLOR DISPLAY CLUSTER, ULTRA BLUE, 5 mm |
| S206CR7-4VF-P | SINGLE COLOR DISPLAY CLUSTER, RED, 5 mm |
| S206CUB500-120VAC-P | SINGLE COLOR DISPLAY CLUSTER, ULTRA BLUE, 5 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S201DL | 功能描述:電容套件 CAP AND IND DSGN KIT 0.2pF-1000pF 50pcs RoHS:否 制造商:Nichicon 電容范圍:10 uF to 680 uF 公差范圍: 電壓范圍:6.3 V to 25 V 產品:Aluminum Organic Polymer Capacitor Kit |
| S201DL | 制造商:Johanson Technology Inc 功能描述:L SERIES DESIGNER KIT, 0201 |
| S201E | 功能描述:SCR 1A 200V RoHS:否 制造商:STMicroelectronics 最大轉折電流 IBO:480 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態 RMS 電流 (It RMS): 正向電壓下降:1.6 V 柵觸發電壓 (Vgt):1.3 V 最大柵極峰值反向電壓:5 V 柵觸發電流 (Igt):35 mA 保持電流（Ih 最大值）:75 mA 安裝風格:Through Hole 封裝 / 箱體:TO-220 封裝:Tube |
| S201ERP | 功能描述:SCR 200V 1A TO92 RoHS:否 類別:分離式半導體產品 >> SCR - 單個 系列:- 其它有關文件:X00619 View All Specifications 產品目錄繪圖:SCR TO-92 Package 標準包裝:1 系列:- SCR 型:靈敏柵極 電壓 - 斷路:600V 電壓 - 柵極觸發器 (Vgt)（最大）:800mV 電壓 - 導通狀態 (Vtm)（最大）:1.35V 電流 - 導通狀態 (It (AV))（最大）:500mA 電流 - 導通狀態 (It (RMS))（最大）:800mA 電流 - 柵極觸發電流 (Igt)（最大）:200µA 電流 - 維持(Ih):5mA 電流 - 斷開狀態（最大）:1µA 電流 - 非重復電涌，50、60Hz (Itsm):9A，10A 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:剪切帶 (CT) 產品目錄頁面:1554 (CN2011-ZH PDF) 其它名稱:497-9067-1 |
| S201-K0.5 | 制造商:ABB Low Voltage Products and Systems 功能描述:Circuit Breaker, Supplementary, K Curve, 1-Pole, 0.5A, 480Y/277 VAC, UL1077, DIN |
發布緊急采購，3分鐘左右您將得到回復。