欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S29CL032J0PQAN102
廠商: SPANSION LLC
元件分類: PROM
英文描述: 1M X 32 FLASH 3.3V PROM, 54 ns, PQFP80
封裝: PLASTIC, MO-108CB-1, QFP-80
文件頁數: 21/78頁
文件大小: 1825K
代理商: S29CL032J0PQAN102
26
S29CD-J & S29CL-J Flash Family
S29CD-J_CL-J_00_B1 September27,2006
Prel imi n ary
Notes:
1. Burst access starts with a rising CLK edge and when ADV# is active.
2. Configurations register 6 is always set to 1 (CR6 = 1). Burst starts and data outputs on the rising CLK edge.
3. CR [13-10] = 1 or three clock cycles
4. CR [13-10] = 2 or four clock cycles
5. CR [13-10] = 3 or five clock cycles
Figure 8.4 Initial Burst Delay Control
8.4.3
Configuration Register
The configuration register sets various operational parameters associated with burst mode. Upon
power-up or hardware reset, the device defaults to the asynchronous read mode and the con-
figuration register settings are in their default state. (See Table 8.6 for the default Configuration
Register settings.) The host system determines the proper settings for the entire configuration
register, and then execute the Set Configuration Register command sequence before attempting
burst operations. The configuration register is not reset after deasserting CE#.
The Configuration Register does not occupy any addressable memory location, but rather, is ac-
cessed by the Configuration Register commands. The Configuration Register is readable at any
time, however, writing the Configuration Register is restricted to times when the Embedded Al-
gorithm is not active. If the user attempts to write the Configuration Register while the
Embedded Algorithm is active, the write operation is ignored and the contents of the Configu-
ration Register remain unchanged.
The Configuration Register is a 16 bit data field which is accessed by DQ15–DQ0. During a read
operation, DQ31–DQ16 returns all zeroes. Also, the Configuration Register reads operate the
same as the Autoselect command reads. When the command is issued, the bank address is
latched along with the command. Read operations to the bank that was specified during the Con-
figuration Register read command return Configuration Register contents. Read operations to the
other bank return flash memory data. Either bank address is permitted when writing the Config-
uration Register read command.
The configuration register can be read with a four-cycle command sequence. See Command Def-
initions on page 71 for sequence details.
CLK
ADV#
Addresses
DQ31-DQ03
DQ31-DQ04
DQ31-DQ05
Valid Address
Three CLK Delay
2nd CLK
3rd CLK
4th CLK
5th CLK
1st CLK
Four CLK Delay
Address 1 Latched
Five CLK Delay
D0
D1
D2
D3
D0
D1
D2
D0
D1
D2
D3
D4
相關PDF資料
PDF描述
S29GL016A10FAI020 1M X 16 FLASH 3V PROM, 100 ns, PBGA64
S29GL032A10TAIR10 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A10TAIR12 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A10TAIR13 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A10TAIR20 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29CL032J0PQFM010 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:32MBIT FLASH - Tape and Reel
S29CL032J0RFAM010 制造商:Spansion 功能描述:
S29GL016A 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAI010 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL016A100BAI012 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
主站蜘蛛池模板: 嘉义县| 海安县| 华亭县| 云浮市| 平凉市| 敖汉旗| 泽库县| 射洪县| 蓬莱市| 安新县| 衡东县| 长春市| 来宾市| 彰武县| 海晏县| 呼和浩特市| 尉犁县| 东海县| 新邵县| 同心县| 深泽县| 莆田市| 靖边县| 离岛区| 阜南县| 土默特右旗| 罗江县| 施甸县| 怀柔区| 阿克陶县| 台北县| 富宁县| 广州市| 文昌市| 巩义市| 兴和县| 镇雄县| 武宁县| 合阳县| 安阳县| 牟定县|