欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： S29GL032A90TAIR23
廠商： SPANSION LLC
元件分類： PROM
英文描述： 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
中文描述： 2M X 16 FLASH 3V PROM, 90 ns, PDSO56
封裝： MO-142EC, TSOP-56
文件頁數： 42/95頁
文件大小： 3585K
代理商： S29GL032A90TAIR23
May 21, 2008 S29GL-A_00_A12
S29GL-A
47
Data
She e t
7.11
Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector feature provides a Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 256 bytes in length,
and uses a Secured Silicon Sector Indicator Bit (DQ7) to indicate whether or not the Secured Silicon Sector is
locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed,
which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is
shipped to the field.
The factory offers the device with the Secured Silicon Sector either customer lockable (standard shipping
option) or factory locked (contact a Spansion sales representative for ordering information). The customer-
lockable version is shipped with the Secured Silicon Sector unprotected, allowing customers to program the
sector after receiving the device. The customer-lockable version also contains the Secured Silicon Sector
Indicator Bit permanently set to a 0. The factory-locked version is always protected when shipped from the
factory, and has the Secured Silicon Sector Indicator Bit permanently set to a 1. Thus, the Secured Silicon
Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory
locked. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon
Sector is enabled.
The Secured Silicon sector address space in this device is allocated as follows:
The system accesses the Secured Silicon Sector through a command sequence (see Write Protect (WP#)
on page 48). After the system writes the Enter Secured Silicon Sector command sequence, it may read the
Secured Silicon Sector by using the addresses normally occupied by the first sector (SA0). This mode of
operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until
power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending
commands to sector SA0.
7.11.1
Customer Lockable: Secured Silicon Sector NOT Programmed or Protected
At the Factory
Unless otherwise specified, the device is shipped such that the customer may program and protect the 256-
byte Secured Silicon sector.
The system may program the Secured Silicon Sector using the write-buffer, accelerated and/or unlock
bypass methods, in addition to the standard programming command sequence. See Command Definitions
Programming and protecting the Secured Silicon Sector must be used with caution since, once protected,
there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the
Secured Silicon Sector memory space can be modified in any way.
The Secured Silicon Sector area can be protected using one of the following procedures:
Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-
system sector protect algorithm as shown in Figure 7.2 on page 46, except that RESET# may be at either
VIH or VID. This allows in-system protection of the Secured Silicon Sector without raising any device pin to
a high voltage. Note that this method is only applicable to the Secured Silicon Sector.
Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then use the alternate
method of sector protection described in Sector Group Protection and Unprotection on page 41.
Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured
Silicon Sector Region command sequence to return to reading and writing within the remainder of the array.
Secured Silicon Sector
Address Range
Standard Factory
Locked
ExpressFlash
Factory Locked
Customer
Lockable
x16
x8
000000h–000007h
000000h-00000Fh
ESN
ESN or determined
by customer
Determined by
customer
000008h–00007Fh
000010h-0000FFh
Unavailable
Determined by
customer
相關PDF資料
PDF描述
S29GL032A90TAIR30 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR32 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR13 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032M10BFIR20 T528 Series - I, M, Z Case Sizes - Face Down Termination Tantalum Surface Mount Capacitor; Capacitance [nom]: 220uF; Working Voltage (Vdc)[max]: 4V; Capacitance Tolerance: +/-20%; Dielectric: Tantalum, Solid; ESR: 9.0mΩ; Lead Style: Surface-Mount Chip; Lead Dimensions: 7343-17; Termination: 100% Tin (Sn); Body Dimensions: 7.3mm x 4.3mm x 1.7mm; Temperature Range: -55C to +105C; Container: Tape & Reel; Qty per Container: 1,000; Features: Face Down Termination
S29GL032M10BFIR22 T528 Series - I, M, Z Case Sizes - Face Down Termination Tantalum Surface Mount Capacitor; Capacitance [nom]: 220uF; Working Voltage (Vdc)[max]: 4V; Capacitance Tolerance: +/-20%; Dielectric: Tantalum, Solid; ESR: 12mΩ; Lead Style: Surface-Mount Chip; Lead Dimensions: 7343-17; Termination: 100% Tin (Sn); Body Dimensions: 7.3mm x 4.3mm x 1.7mm; Temperature Range: -55C to +105C; Container: Tape & Reel; Qty per Container: 1,000; Features: Face Down Termination
相關代理商/技術參數
參數描述
S29GL032A90TAIR30 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR31 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR32 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR33 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A90TAIR40 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 岳阳市| 北碚区| 黄山市| 铜山县| 洱源县| 博爱县| 鹤峰县| 玉林市| 内黄县| 禄劝| 咸阳市| 若尔盖县| 闽清县| 元阳县| 仁寿县| 太原市| 获嘉县| 津市市| 普定县| 汾西县| 富民县| 横山县| 太湖县| 南平市| 白朗县| 米易县| 玛曲县| 高雄市| 秦皇岛市| 河西区| 和平区| 临夏县| 皋兰县| 县级市| 邳州市| 图片| 堆龙德庆县| 盱眙县| 富蕴县| 高要市| 上饶县|