- 您現在的位置：買賣IC網 > PDF目錄85358 > SCDV5542 5X5 DOT MATRIX DISPLAY, SUPER RED, 3.2 mm PDF資料下載
參數資料
| 型號： | SCDV5542 |
| 元件分類： | 顯示用LED |
| 英文描述： | 5X5 DOT MATRIX DISPLAY, SUPER RED, 3.2 mm |
| 封裝： | ROHS COMPLIANT, PLASTIC, DIP-14 |
| 文件頁數： | 2/16頁 |
| 文件大小： | 675K |
| 代理商： | SCDV5542 |
SCDV5540, SCDV5541, SCDV5542, SCDV5543, SCDV5544
2006-01-23
10
Row Strobing
Multiplexer and Display Driver
The four characters are row multiplexed with RAM resident column
data. The strobe rate is established by the internal or external
MUX Clock rate. The MUX Clock frequency is divided by a 320
counter chain. This results in a typical strobe rate of 750 Hz. By
pulling the Clock SEL line low, the display can be operated from an
external MUX Clock. The external clock is attached to the CLK I/O
connection (pin 8). The maximum external MUX Clock frequency
should be limited to 1.0 MHz.
An asynchronous hardware Reset Pin is also provided. Bringing
this pin low will clear the Character Address Register, Control
Word Register, RAM, and blanks the display. This action leaves the
display set at Character Address 0, and the Brightness Level set at
100%.
Electrical & Mechanical Considerations
Interconnect Considerations
Optimum product performance can be had when the following
electrical and mechanical recommendations are adopted. The
SCDV554X’s IC is constructed in a high speed CMOS process,
consequently high speed noise on the SERIAL DATA, SERIAL
DATA CLOCK, LOAD and RESET lines may cause incorrect data
to be written into the serial shift register. Adhere to transmission
line termination procedures when using fast line drivers and long
cables (> 10 cm).
Good digital grounds (pins 7 and 14) and power supply decoupling
(pins 10, 11 and 12) will insure that I
CC (< 400 mA peak) switching
currents do not generate localized ground bounce. Therefore it is
recommended that each display package use a 0.1 F and 20 F
capacitor between V
CC and ground.
When the internal MUX Clock is being used connect the CLKSEL
pin to V
CC. In those applications where RESET will not be con-
nected to the system’s reset control, it is recommended that this
pin be connected to the center node of a series 0.1 F and 100 k
RC network. Thus upon initial power up the RESET will be held
low for 10 ms allowing adequate time for the system power supply
to stabilize.
ESD Protection
The input protection structure of the SCDV554X provides signifi-
cant protection against ESD damage. It is capable of withstanding
discharges greater than 2.0 kV. Take all the standard precautions,
normal for CMOS components. These include properly grounding
personnel, tools, tables, and transport carriers that come in contact
with unshielded parts. If these conditions are not, or cannot be
met, keep the leads of the device shorted together or the parts in
anti-static packaging.
Soldering Considerations
The SCDV554X can be hand soldered with SN63 solder using a
grounded iron set to 260°C.
Wave soldering is also possible following these conditions: Pre-
heat that does not exceed 93°C on the solder side of the PC board
or a package surface temperature of 85°C. Water soluble organic
acid flux (except carboxylic acid) or rosin-based RMA flux without
alcohol can be used.
Wave temperature of 245°C ± 5°C with a dwell between 1.5 sec. to
3.0 sec. Exposure to the wave should not exceed temperatures
above 260°C for five seconds at 1.59 mm (0.063") below the seat-
ing plane. The packages should not be immersed in the wave.
Post Solder Cleaning Procedures
The least offensive cleaning solution is hot D.I. water (60°C) for
less than 15 minutes. Addition of mild saponifiers is acceptable. Do
not use commercial dishwasher detergents.
For faster cleaning, solvents may be used. Exercise care in choos-
ing solvents as some may chemically attack the nylon package. For
further information refer to Appnotes 18 and 19 at
www.osram-os.com
An alternative to soldering and cleaning the display modules is to
use sockets. Naturally, 14 pin DIP sockets 7.62 mm (0.300") wide
with 2.54 mm (0.100") centers work well for single displays. Multi-
ple display assemblies are best handled by longer SIP sockets or
DIP sockets when available for uniform package alignment. Socket
manufacturers are Aries Electronics, Inc., Frenchtown, NJ; Garry
Manufacturing, New Brunswick, NJ; Robinson-Nugent, New
Albany, IN; and Samtec Electronic Hardward, New Albany, IN.
For further information refer to Appnote 22 at www.osram-os.com
IDXX5186
Row 0
Row 1
Row 2
Row 3
Row 4
01 2 3 4
Columns
Load Row 0
Load
4
Row 4
Columns
1
0
2 3
Row 3
Row 1
Row 0
Row 2
Load Row 1
Columns
Row 4
1
0
2
4
3
Load Row 2
Row 2
Row 1
Row 3
Row 0
Row 4
0
Columns
2
13 4
Load Row 3
Row 0
Row 3
Row 1
Row 2
Row 4
Columns
01 2
4
3
Row 2
Row 1
Row 3
Row 0
Load Row 4
Row
相關PDF資料 |
PDF描述 |
|---|---|
| SL-PAR30/B/P11/50/E30/ND/26/LAC | SINGLE COLOR LED |
| SL-PAR30/B/P12/30/E50/TD/27/LAC | SINGLE COLOR LED |
| SPD9442SMSS | PHOTO DIODE |
| SFH6186-2T | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| SML-211WTT86 | SINGLE COLOR LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCDV5543 | 功能描述:LED 顯示器和配件 5x5 Green 0.126" 4-CHARACTER RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| SCDV5544 | 功能描述:LED 顯示器和配件 5x5 Hi-Eff Green 0.126" 4-CHARACTER RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| SCDX | 功能描述:XLR 連接器 HINGED COVER D-SIZE RoHS:否 制造商:Neutrik 標準:Standard XLR 產品類型:Connectors 型式:Female 位置/觸點數量:3 端接類型:Solder 安裝風格:Cable 方向:Vertical |
| SCDX-5-GREEN | 功能描述:XLR 連接器 D SZ HNGD SEAL COVER PLASTIC - GREEN RoHS:否 制造商:Neutrik 標準:Standard XLR 產品類型:Connectors 型式:Female 位置/觸點數量:3 端接類型:Solder 安裝風格:Cable 方向:Vertical |
| SCDX-6 | 制造商:Neutrik USA Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。