- 您現在的位置：買賣IC網 > Datasheet目錄46 > SE97BTP,547 (NXP Semiconductors)IC TEMP SENSOR DIMM 8HWSON Datasheet資料下載
參數資料
| 型號： | SE97BTP,547 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 9/53頁 |
| 文件大小： | 386K |
| 描述： | IC TEMP SENSOR DIMM 8HWSON |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 1 |
| 功能： | 溫度監控系統（傳感器），DIMM DDR 內存 |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±3°C（最小值） |
| 拓撲： | ADC（三角積分型），比較器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-WSON |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 847 (CN2011-ZH PDF) |
| 其它名稱： | 568-5055-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
SE97B_1
?NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 27 January 2010
9 of 53
NXP Semiconductors
SE97B
DDR memory module temp sensor with integrated SPD
7.3.2 EVENT
thresholds
7.3.2.1 Alarm window
The device provides a comparison window with an UPPER trip point and a LOWER trip
point, programmed through the Upper Boundary Alarm Trip register (02h), and Lower
Boundary Alarm Trip register (03h). The Upper Boundary Alarm Trip register holds the
upper temperature trip point, while the Lower Boundary Alarm Trip register holds the lower
temperature trip point as modified by hysteresis as programmed in the Configuration
register. When enabled, the EVENT
output triggers whenever entering or exiting (crossing
above or below) the alarm window.
" Advisory note:
NXP device: The EVENT
output can be cleared through the clear EVENT bit or
SMBus Alert Response Address (ARA).
Competitor device: The EVENT
output can be cleared only through the clear
EVENT bit.
Work-around: Only clear EVENT
output using the EVENT bit if both NXP and
competitor devices are used.
The Upper Boundary Alarm Trip should always be set above the Lower Boundary Alarm
Trip.
The alarm window limit is immediately compared with the temperature register even if it
has not been recently updated (e.g., device has been in standby) when the EVENT
is
turned on (CONFIG[3]).
Consider waiting one conversion cycle (125 ms) after setting the alarm window limit
before enabling the EVENT
output/comparing the alarm window limit with the temperature
register to ensure that there is correct data in the temperature register.
If SMBUS[2] is set, then the alarm window limit will only be compared to the Temperature
register after it has been updated when EVENT
is turned on.
7.3.2.2 Critical trip
The T
th(crit)
temperature setting is programmed in the Critical Alarm Trip register (04h) as
modified by hysteresis as programmed in the Configuration register. When the
temperature reaches the critical temperature value in this register (and EVENT
is
enabled), the EVENT
output asserts and cannot be de-asserted until the temperature
drops below the critical temperature threshold. The Event cannot be cleared through the
clear EVENT bit or SMBus Alert.
The Critical Alarm Trip should always be set above the Upper Boundary Alarm Trip.
The critical trip limit is immediately compared with the temperature register even if it has
not been recently updated (e.g., device has been in standby) when the EVENT
is turned
on (CONFIG[3]).
Consider waiting one conversion cycle (125 ms) after setting the critical trip limit before
enabling the EVENT
output/comparing the critical trip limit with the temperature register to
ensure that there is correct data in the temperature register.
If SMBUS[2] is set, then the alarm window limit will only be compared to the Temperature
register after it has been updated when EVENT
is turned on.
相關PDF資料 |
PDF描述 |
|---|---|
| SE98ATP,547 | IC TEMP SENSOR DDR 8-HWSON |
| SG6901ASZ | IC PFC CTLR AVERAGE CURR 20SOIC |
| SG6932SZ | IC PFC CONTROLLER CCM 16SOP |
| SG6961SY | IC PFC CTRLR AVERAGE CURR 8SOIC |
| SI3500-A-GM | IC POE SWITCH PWR OVER LAN 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SE97PW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V |
| SE97PW,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SE97PW-T | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC TS +SPD DIMM RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SE97TK | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V |
| SE97TK,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。