- 您現在的位置：買賣IC網 > PDF目錄385856 > SP8107 Three Channel High Performance Laser Driver PDF資料下載
參數資料
| 型號： | SP8107 |
| 英文描述： | Three Channel High Performance Laser Driver |
| 中文描述： | 三通道高性能激光驅動器 |
| 文件頁數： | 1/3頁 |
| 文件大小： | 146K |
| 代理商： | SP8107 |
Advanced
SP8107
Rev. 09/05/03 SP8107 – Three Channel Laser Driver
Copyright 2003 Sipex Corporation
SIPEX RESERVES THE RIGHT TO MAKE CHANGES TO THIS DATASHEET. CALL FOR UPDATES: 1-978-667-8700.
SIPEX CONFIDENTIAL, ADVANCED & PROPRIETARY. DO NOT DISTRIBUTE OR
COPY
page
1
of
3
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
IR
I2
I3
RF
EN2
EN3
ENABLE
OSCEN
Vcc
Iout A
GND
RSA
RSB
Iout B
SELA
Vcc
SP8107
SSOP-16
Three Channel High Performance Laser Driver
FEATURES
Three current controlled inputs with independent
ENABLE/DISABLE
Two selectable outputs for grounded laser diodes
Output current up to 400mA (250mA per input channel)
Independent swing for each output channel controlled
by external resistor
On-chip oscillator with resistor controlled frequency
Single 5V power supply
Common ENABLE and oscillator ENABLE inputs
TTL/CMOS logic level control signals
Small SSOP16 package
APPLICATION
DVD-RAM with CD-RW capability
DVD-RW with CD-RW capability
Writable data storage optical devices
GENERAL DESCRIPTION
The SP8107 is a three channel laser diode driver specifically designed for high speed DVD-RW or DVD-
RAM applications. It operates two grounded laser diodes (650nm for DVD and 780nm for CD) and
features three input channels that allow setting of three different optical power levels. The first channel
(IR) has lower gain (100mA/mA) and output current (up to 200mA) and is used as a read channel. The
second (I2) and third (I3) channels have higher gain (250mA/mA) and output current (up to 250mA) and
are used as write channels. Each write channel may be switched on/off at very fast switching speeds with
TTL/CMOS logic level signals applied to EN2 and EN3 inputs - channels are enabled at low logic level
and disabled at high logic level. Outputs of all channels are summed together and connected to one of the
outputs I
OUT
A or I
OUT
B depending on logic signal at the input SELA. High logic level at SELA selects
output I
OUT
A, while low logic level selects output I
OUT
B. Inputs IR, I2, and I3 are current-controlled with
200 ohm DC impedance but allow voltage control by using external limiting resistors.
An on-chip oscillator is used to reduce laser mode hopping in read mode. The frequency of this oscillator
may be changed by an external resistor connected to the RF pin. Oscillator swing can be set separately for
I
OUT
A and I
OUT
B outputs by two resistors connected to RSA and RSB pins respectively. The oscillator is
enabled by high logic level at the OSCEN pin.
Low logic level at the ENABLE pin disables the entire device. Supply current in disabled mode is below
100uA. Pins EN2 and EN3 have internal pull-up resistors. Pins ENABLE, OSCEN, and SELA have
internal pull-down resistors.
相關PDF資料 |
PDF描述 |
|---|---|
| SP8110 | Two-Channel Modulation IC for Laser Diode |
| SP8110ER | Two-Channel Modulation IC for Laser Diode |
| SP8126CB-3 | High Speed Differential APC Amplifier |
| SP8126 | High Speed Differential APC Amplifier |
| SP8126B | High Speed Differential APC Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP810EK-2-3 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3 Pin Microprocessor Supervisor Circuit |
| SP810EK-2-3/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3 Pin Microprocessor Supervisor Circuit |
| SP810EK-2-6 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3 Pin Microprocessor Supervisor Circuit |
| SP810EK-2-6/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3 Pin Microprocessor Supervisor Circuit |
| SP810EK-2-9 | 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。