欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TC74A7-5.0VCTTRG
廠商: Microchip Technology
文件頁數: 7/16頁
文件大小: 338K
描述: IC DGTL THERM SNSR 5.0V SOT23A-5
標準包裝: 3,000
功能: 溫度監控系統(傳感器)
傳感器類型: 內部
感應溫度: -40°C ~ 125°C
精確度: ±3°C(最小值)
拓撲: ADC(三角積分型),寄存器庫
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: SC-74A,SOT-753
供應商設備封裝: SOT-23-5
包裝: 帶卷 (TR)
?2002 Microchip Technology Inc.
DS21462C-page 7
TC74
FIGURE 3-1:
SMBus/I
2
C Protocols.
3.3
START Condition (S)
The TC74 continuously monitors the SDA and SCLK
lines for a START condition (a high-to-low transition of
SDA while SCLK is high) and will not respond until this
condition is met.
3.4
Address Byte
Immediately following the START condition, the host
must transmit the address byte to the TC74. The states
of A2, A1 and A0 determine the SMBus/I
2
C address for
the TC74. The 7-bit address transmitted in the serial bit
stream must match for the TC74 to respond with an
Acknowledge (indicating the TC74 is on the bus and
ready to accept data). The 8-bit in the address byte is
a Read/Write bit. This bit is a 1 for a read operation or
0 for a write operation. During the first phase of any
transfer, this bit will be set = 0, indicating that the
command byte is being written.
3.5
Acknowledge (ACK)
Acknowledge (ACK) provides a positive handshake
between the host and the TC74. The host releases
SDA after transmitting 8 bits. The host then generates
a ninth clock cycle to allow the TC74 to pull the SDA
line low. This action acknowledges that the TC74
successfully received the previous 8 bits of data or
address.
3.6
Data Byte
After a successful ACK of the address byte, the host
must transmit the data byte to be written, or clock-in the
data to be read (see the appropriate timing diagrams).
ACK will be generated upon a successful write of a
data byte into the TC74.
3.7
STOP Condition (P)
Communications must be terminated by a STOP
condition (a low-to-high transition of SDA while SCLK
is high). The STOP condition must be communicated
by the transmitter to the TC74. Refer to Figure 1-1,
Timing Diagrams, for serial bus timing.
S
Address
WR
ACK
Command
ACK
Data
ACK
P
8 Bits
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
writing to.
Data Byte: data goes
into the register set
by the command byte.
Write Byte Format
Read Byte Format
S
Address
WR
ACK
Command
ACK
S
Address
RD   ACK    Data    NACK
P
7 Bits
8 Bits
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
reading from.
Slave Address: repeated
due to change in data-
flow direction.
Data Byte: reads from
the register set by the
command byte.
Receive Byte Format
S
Address
RD    ACK    Data
NACK    P
7 Bits
8 Bits
Data Byte: reads data from
the register commanded by
the last Read Byte or Write
Byte transmission.
S = START Condition
P = STOP Condition
Shaded = Slave Transmission
相關PDF資料
PDF描述
TC77-5.0MOATR IC THERMAL SENSOR SPI 5V 8-SOIC
TC9402EJD IC V-FREQ/FREQ-V CONV 14CDIP
TCN75-5.0MUAG IC TEMP SENSOR SRL 5.0V 8MSOP
TEA1750T/N1,518 IC PFC CONTROLLER DCM16SOIC
TEA1751T/N1,518 IC CTRLR GREENCHIP SMPS 16-SOIC
相關代理商/技術參數
參數描述
TC74AC00F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:QUAD 2 - INPUT NAND GATE
TC74AC00F(F) 制造商:Toshiba 功能描述:74AC Quad 2-Input NAND Gate 14SOP Bulk 制造商:Toshiba America Electronic Components 功能描述:IC, 74 series logic 制造商:Toshiba 功能描述:NAND Gate 4-Element 2-IN CMOS 14-Pin SOP Tube
TC74AC00F_12 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quad 2-Input NAND Gate
TC74AC00FN 功能描述:IC GATE NAND QUAD 2INP 14-SOL RoHS:否 類別:集成電路 (IC) >> 邏輯 - 柵極和逆變器 系列:74AC 標準包裝:2,000 系列:74LCX 邏輯類型:逆變器,緩沖器 電路數:1 輸入數:8 特點:三態 電源電壓:2 V ~ 3.6 V 電流 - 靜態(最大值):10µA 輸出電流高,低:24mA,24mA 邏輯電平 - 低:0.7 V ~ 0.8 V 邏輯電平 - 高:1.7 V ~ 2 V 額定電壓和最大 CL 時的最大傳播延遲:6.5ns @ 3.3V,50pF 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 供應商設備封裝:20-SSOP 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 包裝:帶卷 (TR)
TC74AC00FN(ELF,M) 制造商:Toshiba America Electronic Components 功能描述:IC 2-INP NAND GATE QUAD 14-SOL 制造商:Toshiba America Electronic Components 功能描述:IC GATE NAND QUAD 2INP 14-SOL
主站蜘蛛池模板: 平和县| 新安县| 永丰县| 桦川县| 南宫市| 云安县| 广灵县| 定日县| 盈江县| 富阳市| 南郑县| 和田市| 康乐县| 乐亭县| 出国| 平乡县| 江都市| 南昌市| 镇巴县| 安庆市| 丰县| 南通市| 前郭尔| 民乐县| 正蓝旗| 奈曼旗| 高阳县| 德清县| 富蕴县| 日土县| 南平市| 徐闻县| 青河县| 乌拉特后旗| 井陉县| 九龙城区| 静宁县| 万源市| 天镇县| 石屏县| 鸡泽县|