- 您現在的位置：買賣IC網 > PDF目錄98217 > THS10082CDAG4 (TEXAS INSTRUMENTS INC) 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 PDF資料下載
參數資料
| 型號： | THS10082CDAG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| 封裝： | GREEN, PLASTIC, TSSOP-32 |
| 文件頁數： | 19/37頁 |
| 文件大小： | 375K |
| 代理商： | THS10082CDAG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
THS10082
SLAS254B MAY 2002 REVISED NOVEMBER 2002
www.ti.com
26
FIFO TRIGGER LEVEL
Bit 2 and bit 3 (TRIG1, TRIG0) of control register 1 are used to set the trigger level of the FIFO (see Table 13). If the trigger
level is reached, the DATA_AV (data available) signal becomes active according to the setting of the signal DATA_AV to
indicate to the processor that the ADC values can be read.
Table 13 shows four different programmable trigger levels for each configuration. The FIFO trigger level, which can be
selected, is dependent on the number of input channels. One channel is considered as two inputs in differential
configuration, or one single-ended input. The processor, therefore, always reads the data from the FIFO in the same order
and is able to distinguish between the channels.
Table 13. FIFO Trigger Level
BIT 3
TRIG1
BIT 2
TRIG0
TRIGGER LEVEL
FOR 1 CHANNEL
(ADC values)
TRIGGER LEVEL
FOR 2 CHANNELS
(ADC values)
0
01
02
0
1
04
1
0
08
1
14
12
TIMING AND SIGNAL DESCRIPTION OF THE THS10082
The reading from the THS10082 and writing to the THS10082 is performed by using the chip select inputs (CS0, CS1),
the write input WR and the read input RD. The write input is configurable to a combined read/write input (R/W). This is
desired in cases where the connected processor consists of a combined read/write output signal (R/W). The two chip select
inputs can be used to interface easily to a processor.
Reading from the THS10082 takes place by an internal RDint signal, which is generated from the logical combination of
the external signals CS0, CS1, and RD (see Figure 35). This signal is then used to strobe the words out of the FIFO and
to enable the output buffers. The last external signal (either CS0, CS1, or RD) to become valid makes RDint active while
the write input (WR) is inactive. The first of those external signals going to its inactive state then deactivates RDint.
Writing to the THS10082 takes place by an internal WRint signal, which is generated from the logical combination of the
external signals CS0, CS1 and WR. This signal is then used to strobe the control words into the control registers 0 and
1. The last external signal (either CS0, CS1, or WR) to become valid makes WRint active while the read input (RD) is
inactive. The first of those external signals going to its inactive state then deactivates WRint.
Read Enable
Write Enable
Control/Data
Registers
CS0
CS1
RD
WR
Data Bits
Figure 35. Logical Combination of CS0, CS1, RD, and WR
相關PDF資料 |
PDF描述 |
|---|---|
| THS10082CDAR | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS10082CDA | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS10082IDA | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS10082IDAR | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS10082IDAG4 | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS10082EVM | 功能描述:EVALUATION MODULE FOR THS10082 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| THS10082IDA | 功能描述:模數轉換器 - ADC 10 BIT High Speed AD RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS10082IDAG4 | 功能描述:模數轉換器 - ADC 10 Bit 8 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1009 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1009CDA | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。