- 您現在的位置：買賣IC網 > PDF目錄98217 > THS1009CDAR (TEXAS INSTRUMENTS INC) 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 PDF資料下載
參數資料
| 型號： | THS1009CDAR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| 封裝： | PLASTIC, TSSOP-32 |
| 文件頁數： | 6/31頁 |
| 文件大?。?/td> | 289K |
| 代理商： | THS1009CDAR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
THS1009
SLAS287A – AUGUST 2000 – REVISED DECEMBER 2002
www.ti.com
14
DETAILED DESCRIPTION
Reference Voltage
The THS1009 has a built-in reference, which provides the reference voltages for the ADC. VREFP is set to 3.5 V
and VREFM is set to 1.5 V. An external reference can also be used through two reference input pins, REFP and
REFM, if the reference source is programmed as external. The voltage levels applied to these pins establish the
upper and lower limits of the analog inputs to produce a full-scale and zero-scale reading respectively.
Analog Inputs
The THS1009 consists of two analog inputs, which are sampled simultaneously. These inputs can be selected
individually and configured as single-ended or differential inputs. The desired analog input channel can be
programmed.
Converter
The THS1009 uses a 10-bit pipelined multistaged architecture which achieves a high sample rate with low power
consumption. The THS1009 distributes the conversion over several smaller ADC sub-blocks, refining the conversion
with progressively higher accuracy as the device passes the results from stage to stage. This distributed conversion
requires a small fraction of the number of comparators used in a traditional flash ADC. A sample-and-hold amplifier
(SHA) within each of the stages permits the first stage to operate on a new input sample while the second through
the eighth stages operate on the seven preceding samples.
Conversion
An external clock signal with a duty cycle of 50% has to be applied to the clock input (CONV_CLK). A new conversion
is started with every falling edge of the applied clock signal. The conversion values are available at the output with
a latency of 5 clock cycles.
SYNC
In multichannel mode, the first SYNC signal is delayed by [7+ (# Channels Sampled)] cycles of the CONV_CLK after
a SYNC reset. This is due to the latency of the pipeline architecture of the THS1009.
Sampling Rate
The maximum possible conversion rate per channel is dependent on the selected analog input channels. Table 1
shows the maximum conversion rate for the different combinations.
Table 1. Maximum Conversion Rate in Continuous Conversion Mode
CHANNEL CONFIGURATION
NUMBER OF
CHANNELS
MAXIMUM CONVERSION
RATE PER CHANNEL
1 single-ended channel
1
8 MSPS
2 single-ended channels
2
4 MSPS
1 differential channel
1
8 MSPS
The maximum conversion rate per channel, fc, is given by:
fc
+ 8 MSPS
# channels
Continuous Conversion Mode
During conversion the ADC operates with a free running external clock signal applied to the input CONV_CLK. With
every falling edge of the CONV_CLK signal a new converted value is available to the databus with the corresponding
read signal. The THS1009 offers up to two analog inputs to be selected. It is important to provide the channel
information to the system; this means knowing which channel is available to the databus. To maintain this channel
integrity, the THS1009 has an output signal SYNC, which is always active low if the data of channel 1 is applied to
the databus.
相關PDF資料 |
PDF描述 |
|---|---|
| THS1009CDA | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1009IDA | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1009IDAR | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1009IDAG4 | 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS1030CDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1009CDARG4 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1009EVM | 功能描述:EVALUATION MODULE FOR THS1009 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| THS1009IDA | 功能描述:模數轉換器 - ADC 10 BIT QUAD ADC w/o RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1009IDAG4 | 功能描述:模數轉換器 - ADC 10-Bit 8 MSPS Dual Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1009IDAR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。