- 您現在的位置：買賣IC網 > PDF目錄98219 > THS1230IPWR (TEXAS INSTRUMENTS INC) 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF資料下載
參數資料
| 型號： | THS1230IPWR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | GREEN, PLASTIC, TSSOP-28 |
| 文件頁數： | 10/25頁 |
| 文件大小： | 884K |
| 代理商： | THS1230IPWR |
www.ti.com
Analog Input Bandwidth
Output Timing
Signal-to-Noise Ratio + Distortion (SINAD)
Effective Number of Bits (ENOB)
Total Harmonic Distortion (THD)
Spurious Free Dynamic Range (SFDR)
THS1230
SLAS291B – OCTOBER 2000 – REVISED MARCH 2004
The analog input bandwidth is defined as the maximum frequency of a 1-dBFS input sine wave that can be
applied to the device for which an extra 3-dB attenuation is observed in the reconstructed output signal.
Output timing td(O) is measured from the 50% level of the CLK input falling edge to the 10%/90% level of the
digital output. The digital output load is not higher than 10 pF.
Output hold time th(O) is measured from the 50% level of the CLK input falling edge to the10%/90% level of the
digital output. The digital output load is not less than 2 pF.
Aperture delay td(A) is measured from the 50% level of the CLK input to the actual sampling instant.
The OE signal is asynchronous.
OE timing td(PZ) is measured from the VIH(min) level of OE to the high-impedance state of the output data. The
digital output load is not higher than 10 pF.
OE timing td(EN) is measured from the VIL(max) level of OE to the instant when the output data reaches VOH(min) or
VOL(max) output levels. The digital output load is not higher than 10 pF.
SINAD is the ratio of the rms value of the measured input signal to the rms sum of all other spectral components
below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is expressed in
decibels.
For a sine wave, SINAD can be expressed in terms of the number of bits. Using the following formula,
N = (SINAD – 1.76)/6.02
it is possible to get a measure of performance expressed as N, the effective number of bits. Thus, effective
number of bits for a device for sine wave inputs at a given input frequency can be calculated directly from its
measured SINAD.
THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured input
signal and is expressed as a percentage or in decibels.
SFDR is the difference in dB between the rms amplitude of the input signal and the peak spurious signal.
18
相關PDF資料 |
PDF描述 |
|---|---|
| THS1230CDWG4 | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1230IPW | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1240IPHP | 1-CH 12-BIT DELTA-SIGMA ADC, PARALLEL ACCESS, PQFP48 |
| THS1240CPHP | 1-CH 12-BIT DELTA-SIGMA ADC, PARALLEL ACCESS, PQFP48 |
| THS1240I | 1-CH 12-BIT DELTA-SIGMA ADC, PARALLEL ACCESS, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1230IPWRG4 | 功能描述:模數轉換器 - ADC Low Power High-Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS124 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH STABILITY MOTOR CONTROL. DIGITAL TACHOMETER. CRANK SHAFT POSITION SENSOR. |
| THS124(TE85R,F) | 制造商:Toshiba 功能描述:Hall Effect Sensor 4-Pin 10-3C1A T/R Cut Tape |
| THS1240 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-BIT 40 MSPS IF SAMPLING COMMUNICATIONS ANALOG-TO-DIGITAL CONVERTER |
| THS1240CPHP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。