- 您現在的位置：買賣IC網 > PDF目錄98223 > THS3201DGNRG4 (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | THS3201DGNRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 13/37頁 |
| 文件大小： | 1116K |
| 代理商： | THS3201DGNRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
PowerPAD DESIGN CONSIDERATIONS
0.060
0.040
0.075
0.025
0.205
0.010
vias
Pin 1
Top View
0.017
0.035
0.094
0.030
0.013
PowerPAD PCB LAYOUT CONSIDERATIONS
DIE
Side View (a)
DIE
End View (b)
Thermal
Pad
Bottom View (c)
SLOS416C – JUNE 2003 – REVISED JUNE 2009 ............................................................................................................................................................. www.ti.com
Socketing a high-speed part like the THS3201 is
not recommended. The additional lead length and
pin-to-pin capacitance introduced by the socket
can create an extremely troublesome parasitic
network which can make it almost impossible to
achieve a smooth, stable frequency response.
Best
results
are
obtained
by
soldering
the
THS3201 parts directly onto the board.
The THS3201 is available in a thermally-enhanced
PowerPAD family of packages. These packages are
constructed using a downset leadframe upon which
the
die
is
mounted
[see
62(a)
and
Figure 62(b)]. This arrangement results in the lead
frame being exposed as a thermal pad on the
underside of the package [see Figure 62(c)]. Because
Figure 63. DGN PowerPAD PCB Etch and
this thermal pad has direct thermal contact with the
Via Pattern
die, excellent thermal performance can be achieved
by providing a good thermal path away from the
thermal pad.
The PowerPAD package allows for both assembly
1. Prepare the PCB with a top side etch pattern as
and thermal management in one manufacturing
shown in Figure 63. There should be etch for the
operation. During the surface-mount solder operation
leads as well as etch for the thermal pad.
(when the leads are being soldered), the thermal pad
can also be soldered to a copper area underneath the
2. Place five holes in the area of the thermal pad.
package. Through the use of thermal paths within this
These holes should be 10 mils in diameter. Keep
copper area, heat can be conducted away from the
them small so that solder wicking through the
package into either a ground plane or other heat
holes is not a problem during reflow.
dissipating device.
3. Additional vias may be placed anywhere along
the thermal plane outside of the thermal pad
The PowerPAD package represents a breakthrough
area. This helps dissipate the heat generated by
in combining the small area and ease of assembly of
the THS3201 IC. These additional vias may be
surface-mount
with
the,
heretofore,
awkward
larger than the 10-mil diameter vias directly under
mechanical methods of heatsinking.
the thermal pad. They can be larger because
they are not in the thermal pad area to be
soldered so that wicking is not a problem.
4. Connect all holes to the internal ground plane.
5. When connecting these holes to the ground
plane, do not use the typical web or spoke via
connection methodology. Web connections have
a high thermal resistance connection that is
Figure 62. Views of Thermally-Enhanced Package
useful for slowing the heat transfer during
soldering operations. This makes the soldering of
vias that have plane connections easier. In this
Although there are many ways to properly heatsink
application, however, low thermal resistance is
the PowerPAD package, the following steps illustrate
desired for the most efficient heat transfer.
the recommended approach.
Therefore,
the
holes
under
the
THS3201
PowerPAD
package
should
make
their
connection to the internal ground plane with a
complete
connection
around
the
entire
circumference of the plated-through hole.
6. The top-side solder mask should leave the
terminals of the package and the thermal pad
area with its five holes exposed. The bottom-side
solder mask should cover the five holes of the
thermal pad area. This prevents solder from
20
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3201
相關PDF資料 |
PDF描述 |
|---|---|
| THS3201MDEP | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3201MDGNEP | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3201MDGNREP | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3201MDREP | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3202DRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS3201DR | 功能描述:高速運算放大器 1.8GHz Current Feedback Amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3201DRG4 | 功能描述:高速運算放大器 1.8GHz Current Feedback Amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3201-EP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.8-GHz LOW-DISTORTION CURRENT-FEEDBACK AMPLIFIER |
| THS3201EVM | 功能描述:放大器 IC 開發工具 THS3201 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| THS3201MDEP(1) | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.8-GHz LOW-DISTORTION CURRENT-FEEDBACK AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。