- 您現在的位置：買賣IC網 > PDF目錄98224 > THS4081CDGN (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | THS4081CDGN |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 7/32頁 |
| 文件大小： | 841K |
| 代理商： | THS4081CDGN |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
THS4081, THS4082
175MHz LOW POWER HIGHSPEED AMPLIFIERS
SLOS274D DECEMBER 1999 REVISED JUNE 2001
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals is often required. The simplest
way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier (see Figure 43).
VI
VO
C1
+
RG
RF
R1
f
–3dB +
1
2
pR1C1
V
O
V
I
+
1
)
R
F
R
G
1
) sR1C1
Figure 43. Single-Pole Low-Pass Filter
circuit layout considerations
To achieve the levels of high frequency performance of the THS408x, follow proper printed-circuit board high
frequency design techniques. A general set of guidelines is given below. In addition, a THS408x evaluation
board is available to use as a guide for layout or for evaluating the device performance.
D Ground planes It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D Proper power supply decoupling Use a 6.8-F tantalum capacitor in parallel with a 0.1-F ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-
F ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-
F capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D Sockets Sockets are not recommended for high-speed operational amplifiers. The additional lead
inductance in the socket pins will often lead to stability problems. Surface-mount packages soldered directly
to the printed-circuit board is the best implementation.
D Short trace runs/compact part placements Optimum high frequency performance is achieved when stray
series inductance has been minimized. To realize this, the circuit layout should be made as compact as
possible, thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting
input of the amplifier. Its length should be kept as short as possible. This will help to minimize stray
capacitance at the input of the amplifier.
D Surface-mount passive components Using surface-mount passive components is recommended for high
frequency amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout, thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
相關PDF資料 |
PDF描述 |
|---|---|
| THS4081CDR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4081CD | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4081IDGNR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4081IDGN | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4081IDR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4081CDGNG4 | 功能描述:高速運算放大器 175-MHz Low-Power Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4081CDGNR | 功能描述:高速運算放大器 175-MHz Low-Power Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4081CDGNRG4 | 功能描述:高速運算放大器 175-MHz Low-Power Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4081CDR | 功能描述:高速運算放大器 175-MHz Low-Power Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4081CDRG4 | 功能描述:高速運算放大器 175-MHz Low-Power Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。