欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: THS4082IDR
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
封裝: GREEN, PLASTIC, SOIC-8
文件頁數: 11/32頁
文件大小: 841K
代理商: THS4082IDR
THS4081, THS4082
175MHz LOW POWER HIGHSPEED AMPLIFIERS
SLOS274D DECEMBER 1999 REVISED JUNE 2001
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD
design considerations (continued)
The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent
power and output power. The designer should never forget about the quiescent heat generated within the
device, especially multiamplifier devices. Because these devices have linear output stages (Class A-B), most
of the heat dissipation is at low output voltages with high output currents. Figure 47 to Figure 50 show this effect,
along with the quiescent heat, with an ambient air temperature of 50
°C. Obviously, as the ambient temperature
increases, the limit lines shown will drop accordingly. The area under each respective limit line is considered
the safe operating area. Any condition above this line will exceed the amplifier’s limits and failure may result.
When using VCC = ±5 V, there is generally not a heat problem, even with SOIC packages. But, when using
VCC = ±15 V, the SOIC package is severely limited in the amount of heat it can dissipate. The other key factor
when looking at these graphs is how the devices are mounted on the PCB. The PowerPAD
devices are
extremely useful for heat dissipation. But, the device should always be soldered to a copper plane to fully use
the heat dissipation properties of the PowerPAD
. The SOIC package, on the other hand, is highly dependent
on how it is mounted on the PCB. As more trace and copper area is placed around the device,
θJA decreases
and the heat dissipation capability increases. The currents and voltages shown in these graphs are for the total
package. For the dual amplifier package (THS4082), the sum of the RMS output currents and voltages should
be used to choose the proper package. The graphs shown assume that both amplifier’s outputs are identical.
Figure 47
Package With
θJA < = 127°C/W
SO-8 Package
θJA = 167°C/W
Low-K Test PCB
VCC = ± 5 V
TJ = 150°C
TA = 50°C
100
80
40
0
01
2
3
Maximum
RMS
Output
Current
mA
140
180
200
45
160
120
60
20
| VO | RMS Output Voltage V
I O||
Maximum Output
Current Limit Line
THS4081
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
Safe Operating
Area
Figure 48
100
10
03
6
9
1000
12
15
Maximum Output
Current Limit Line
SO-8 Package
θJA = 167°C/W
Low-K Test PCB
SO-8 Package
θJA = 98°C/W
High-K Test PCB
TJ = 150°C
TA = 50°C
| VO | RMS Output Voltage V
Maximum
RMS
Output
Current
mA
I O||
VCC = ± 15 V
DGN Package
θJA = 58.4°C/W
THS4081
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
Safe Operating
Area
相關PDF資料
PDF描述
THS4082ID 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS4082CDGNRG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS4082IDGNRG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS4082CDRG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS4082IDG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
相關代理商/技術參數
參數描述
THS4082IDRG4 功能描述:高速運算放大器 175-MHz Low-Power Vltg-Feedback Dual RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS412 制造商:TI 制造商全稱:Texas Instruments 功能描述:200MHz, CMOS OPERATIONAL AMPLIFIER WITH SHUTDOWN
THS4120 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-SPEED FULLY DIFFERENTIAL I/O AMPLIFIERS
THS4120CD 功能描述:特殊用途放大器 Fully Differential CMOS RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比(最小值): 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
THS4120CDG4 功能描述:特殊用途放大器 3.3V 100 MHz 43 V/us Fully Diff CMOS Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比(最小值): 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
主站蜘蛛池模板: 绍兴市| 宁夏| 镇原县| 阿城市| 连南| 平山县| 庄浪县| 巴林右旗| 平安县| 公安县| 肃宁县| 白朗县| 克东县| 错那县| 定远县| 会理县| 河西区| 信丰县| 富平县| 珲春市| 昭觉县| 秦皇岛市| 利津县| 盈江县| 准格尔旗| 淮滨县| 张家界市| 隆昌县| 遵义县| 渭源县| 定陶县| 肥西县| 济南市| 天门市| 连云港市| 文安县| 商丘市| 永安市| 怀来县| 荔浦县| 和顺县|