- 您現在的位置：買賣IC網 > PDF目錄98229 > THS7365IPW (TEXAS INSTRUMENTS INC) 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 PDF資料下載
參數資料
| 型號： | THS7365IPW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 31/52頁 |
| 文件大小： | 1599K |
| 代理商： | THS7365IPW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
OUTPUT MODE OF OPERATION:
www.ti.com.................................................................................................................................................................................................. SBOS467 – MARCH 2009
Macrovision, the CVBS signal can reach up to
For 720p, 1080i, and 1080p signals, or for the the
1.23 VPP at the input, or 2.46 VPP at the output of the
480i, 576i, 480p, and 576p signals with sync present
THS7365. In contrast, other signals are typically
on the P’B and P’R channels, the lowest voltage of the
1 VPP or 0.7 VPP at the input which translate to an
sync is –300 mV below the midpoint reference
output voltage of 2 VPP or 1.4 VPP. The output bias
voltage of 0 V. The P’B and P’R signals allow a signal
voltage must account for a worst-case situation,
to be as low as –350 mV below the midpoint
depending on the signals involved.
reference voltage of 0 V. This allowance corresponds
to 100% yellow for P’B signal or 100% cyan for P’R
One other issue that must be taken into account is
signal . Because the P’B and P’R signal voltage can
the dc-bias point is a function of the power supply. As
be lower than the sync voltage, there exists a
such, there is an impact on system PSRR. To help
potential for clipping of the signal for a short period of
reduce this impact, the input capacitor combines with
time if the signals drop below the sync voltage.
the pull-up resistance to function as a low-pass filter.
Additionally, the time to charge the capacitor to the
The THS7365 does include a 150-mV input level
final dc bias point is a function of the pull-up resistor
shift, or 300 mV at the output, that should mitigate
and the input capacitor size. Lastly, the input
any clipping issues. For example, if a STC is used,
capacitor forms a high-pass filter with the parallel
then the bottom of the sync is 300 mV at the output.
impedance of the pull-up resistor and the 800-k
If the signal does go the lowest level, or 50 mV lower
resistor. In general, it is good to have this high-pass
than the sync at the input, then the instantaneous
filter at approximately 3 Hz to minimize any potential
output is (–50 mV + 150 mV) × 2 = 200 mV at the
droop on a P’B, P’R, or non-sync B’ or R’ signal. A
output.
0.1-
F input capacitor with a 3.3-M pull-up resistor
Another potential risk is that if this signal (100%
equates to approximately a 2.5-Hz high-pass corner
yellow for P’B or 100% cyan for P’R) exists for several
frequency.
pixels, then the STC circuit engages to raise the
This mode of operation is recommended for use with
voltage back to 0 V at the input. This function can
chroma (C’), P’B, P’R, U’, V’, and non-sync R'G'B'
cause a 50-mV level shift at the input midway through
signals. This method can also be used with sync
the active video signal. This effect is undesirable and
signals if desired. The benefit of using the STC
can cause errors in the decoding of the signal.
function over the ac-bias configuration on embedded
It is therefore recommended to use ac bias mode for
sync signals is that the STC maintains a constant
component P’B and P’R signals when ac-coupling is
back-porch voltage as opposed to a back-porch
desired.
voltage that fluctuates depending on the video
content. Because the high-pass corner frequency is a
very low 2.5 Hz, the impact on the video signal is
negligible relative to the STC configuration.
DC-COUPLED
One question may arise over the P’B and P’R
The THS7365 incorporates a rail-to-rail output stage
channels. For 480i, 576i, 480p, and 576p signals, a
that can be used to drive the line directly without the
sync may or may not be present. If no sync exists
need for large ac-coupling capacitors. This design
within the signal, then it is obvious that ac-bias is the
offers
the
best
line
tilt
and
field
tilt
(droop)
preferred method of ac-coupling the signal.
performance because no ac-coupling occurs. Keep in
mind that if the input is ac-coupled, then the resulting
tilt as a result of the input ac-coupling continues to be
seen on the output, regardless of the output coupling.
The 80-mA output current drive capability of the
THS7365 is designed to drive two video lines
simultaneously—essentially,
a
75-
load—while
keeping the output dynamic range as wide as
possible. Figure 120 shows the THS7365 driving two
video lines while keeping the output dc-coupled.
Copyright 2009, Texas Instruments Incorporated
37
Product Folder Link(s): THS7365
相關PDF資料 |
PDF描述 |
|---|---|
| THS7368IPWR | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| THS7368IPW | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| THS7372IPWR | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
| THS7372IPW | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
| THS7374IPWR | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS7365IPWR | 功能描述:視頻放大器 6Ch Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7368 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:6-Channel Video Amplifier with 3-SD and 3-SD/ED/HD/Full-HD Filters and 6-dB Gain |
| THS7368EVM | 功能描述:放大器 IC 開發(fā)工具 THS7368EVM Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| THS7368IPW | 功能描述:視頻放大器 6-Ch Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7368IPW | 制造商:Texas Instruments 功能描述:Video Amplifier IC 制造商:Texas Instruments 功能描述:IC, VIDEO AMPLIFIER, HEX, 350MHZ TSSOP20 |
發(fā)布緊急采購，3分鐘左右您將得到回復。