- 您現在的位置：買賣IC網 > PDF目錄98234 > TLC1518IPWR (TEXAS INSTRUMENTS INC) 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 PDF資料下載
參數資料
| 型號： | TLC1518IPWR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封裝： | GREEN, PLASTIC, TSSOP-20 |
| 文件頁數： | 8/37頁 |
| 文件大小： | 572K |
| 代理商： | TLC1518IPWR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
TLC1514, TLC1518
5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN
SLAS252 – DECEMBER 1999
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
modes using the FIFO: modes 01, 10, 11 timing (continued)
Mode 10 (sweep mode) requires reconfiguration at the start of each new sweep sequence. Once the FIFO is
filled up to the programmed threshold, the host has the option to either read the FIFO or configure for other
modes. Once the FIFO is read, the host must reconfigure the device before the next sweep sequence can be
started. So the sequence is either configure : triggered conversions : FIFO read : configure. or configure :
triggered conversions : configure : .... Each configure clears the FIFO and the action that follows the configure
command depends on the mode setting of the device.
Mode 11 (repeat sweep mode) requires one cycle configuration. This sweep sequence can be repeated without
reconfiguration. Once the FIFO is filled up to the programmed threshold, the host has the option to either read
the FIFO or configure for other modes. So the sequence is either configure : triggered conversions : FIFO read
: triggered conversions : FIFO read ... or configure : triggered conversions : configure : .... Each configure clears
the FIFO and the action that follows the configure command depends on the mode setting of the device.
CS
CSTART
SDI
INT
SDO
From Channel 0
FS
(DSP)
From Channel 3
Configure
Conversion
Read FIFO
#1
#2
#3
#4
Top of FIFO
tsample(1)
Read FIFO
#1
From Channel 0
Conversion
From Channel 3
Conversion
Repeat
Second FIFO Read
Repeat
tsample(2)
tsample(3)
First FIFO Read
tconvert
tSample(i) > = MIN(tSample)
tsample(4)
Command = Configure write for mode 10 or 11, FIFO threshold = 1/2, sweep seq = 0–1–2–3.
Command = Read FIFO
Figure 12. TLC1514/TLC1518 Mode 10/11 DSP Serial Interface (conversions triggered by FS)
相關PDF資料 |
PDF描述 |
|---|---|
| TLC1518IPWG4 | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLC1514ID | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| TLC1514IPW | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| TLC1514IPWRG4 | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| TLC1514IDR | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC1518IPWRG4 | 功能描述:模數轉換器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1518PW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN |
| TLC154 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM/ROM-Based 8-Bit Microcontroller Series |
| TLC1541 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS |
| TLC1541CDW | 功能描述:模數轉換器 - ADC 10bit A/D w/Ser In RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。