欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TLC1541CN
廠商: TEXAS INSTRUMENTS INC
元件分類: ADC
英文描述: 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20
封裝: ROHS COMPLIANT, PLASTIC, DIP-20
文件頁數: 2/13頁
文件大小: 182K
代理商: TLC1541CN
TLC1541
10-BIT ANALOG-TO-DIGITAL CONVERTER
WITH SERIAL CONTROL AND 11 INPUTS
SLAS073C – DECEMBER 1995 – REVISED AUGUST 1996
10
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
It is possible to connect SYSTEM CLOCK and I/O CLOCK together in special situations in which controlling-circuitry
points must be minimized. In this case, the following special points must be considered in addition to the requirements
of the normal control sequence previously described.
1.
This device requires the first two clocks to recognize that CS is at a valid low level when the common clock
signal is used as an I/O CLOCK. When CS is recognized by the device to be at a high level, the common clock
signal is used for the conversion clock also.
2.
A low CS must be recognized before the I/O CLOCK can shift in an analog channel address. The device
recognizes a CS transition when the SYSTEM CLOCK terminal receives two positive edges and then a
negative edge. For this reason, after a CS negative edge, the first two clock cycles do not shift in the address.
Also, upon shifting in the address, CS must be raised after the tenth valid (12 total) I/O CLOCK. Otherwise,
additional common-clock cycles are recognized as I/O CLOCK cycles and shift in an erroneous address.
For certain applications, such as strobing applications, it is necessary to start conversion at a specific point in time.
This device accommodates these applications. Although the on-chip sample-and-hold begins sampling upon the
negative edge of the fourth valid I/O CLOCK cycle, the hold function does not initiate until the negative edge of the
tenth valid I/O CLOCK cycle. Thus, the control circuitry can leave the I/O CLOCK signal in its high state during the
tenth valid I/O CLOCK cycle until the moment at which the analog signal must be converted. The TLC1541 continues
sampling the analog input until the eighth valid falling edge of the I/O CLOCK. The control circuitry or software then
immediately lowers the I/O CLOCK signal and holds the analog signal at the desired point in time and starts the
conversion.
相關PDF資料
PDF描述
TLC1541CNE4 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20
TLC1541CFNG3 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC20
TLC1542MJ 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP20
TLC1542MFK 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CQCC20
TLC1542QDWR 11-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
相關代理商/技術參數
參數描述
TLC1541CNE4 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1541DW 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS
TLC1541FN 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS
TLC1541IDW 功能描述:模數轉換器 - ADC 10bit A/D w/Ser In RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1541IDWG4 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
主站蜘蛛池模板: 沧州市| 阿克| 靖州| 富阳市| 江城| 桃源县| 苍山县| 石家庄市| 阿荣旗| 辽宁省| 兴宁市| 漳州市| 博白县| 徐水县| 大足县| 呼伦贝尔市| 库伦旗| 韶关市| 宣威市| 台北县| 西青区| 梧州市| 屯门区| 天祝| 昌平区| 大宁县| 临泉县| 潜山县| 新密市| 牡丹江市| 垫江县| 胶南市| 政和县| 渑池县| 滨海县| 都昌县| 沧源| 卫辉市| 宣化县| 仲巴县| 无为县|