欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TLC545CFN
廠商: TEXAS INSTRUMENTS INC
元件分類: ADC
英文描述: 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC28
封裝: GREEN, PLASTIC, LCC-28
文件頁數: 3/15頁
文件大小: 202K
代理商: TLC545CFN
TLC545C, TLC545I, TLC546C, TLC546I
8-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 19 INPUTS
SLAS066B – DECEMBER 1985 – REVISED OCTOBER 1996
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
It is possible to connect SYSTEM CLOCK and I/O CLOCK together in special situations in which controlling circuitry
points must be minimized. In this case, the following special points must be considered in addition to the requirements
of the normal control sequence previously described.
1.
The first two clocks are required for this device to recognize CS is at a valid low level when the common clock
signal is used as an I/O CLOCK. When CS is recognized by the device to be at a high level, the common clock
signal is used for the conversion clock also.
2.
A low CS must be recognized before the I/O CLOCK can shift in an analog channel address. The device
recognizes a CS transition when the SYSTEM CLOCK terminal receives two positive edges and then a
negative edge. For this reason, after a CS negative edge, the first two clock cycles do not shift in the address.
Also, upon shifting in the address, CS must be raised after the eighth valid (10 total) I/O CLOCK. Otherwise,
additional common clock cycles are recognized as I/O CLOCKS and shift in an erroneous address.
For certain applications, such as strobing applications, it is necessary to start conversion at a specific point in time.
This device accommodates these applications. Although the on-chip sample and hold begins sampling upon the
negative edge of the fourth valid I/O clock cycle, the hold function is not initiated until the negative edge of the eighth
valid I/O clock cycle. Thus, the control circuitry can leave the I/O clock signal in its high state during the eighth valid
I/O clock cycle, until the moment at which the analog signal must be converted. The TLC545/546 continues sampling
the analog input until the eighth valid falling edge of the I/O clock. The control circuitry or software must then
immediately lower the I/O clock signal to initiate the hold function at the desired point in time and to start conversion.
相關PDF資料
PDF描述
TLC546IN 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP28
TLC545IFN 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC28
TLC545IN 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP28
TLC548CP 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8
TLC548CD 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
相關代理商/技術參數
參數描述
TLC545CN 功能描述:模數轉換器 - ADC 8bit 20Chl A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC545CNG4 功能描述:模數轉換器 - ADC 8B 76 kSPS ADC 19Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC545I 制造商:TI 制造商全稱:Texas Instruments 功能描述:8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 19 INPUTS
TLC545IFN 功能描述:模數轉換器 - ADC 8bit 20Chl A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC545IFN 制造商:Texas Instruments 功能描述:8BIT ADC 76KSPS SMD 制造商:Texas Instruments 功能描述:8BIT ADC, 76KSPS, SMD
主站蜘蛛池模板: 汶上县| 会宁县| 苏尼特左旗| 锡林浩特市| 泰兴市| 句容市| 锡林郭勒盟| 洪湖市| 明溪县| 柳江县| 新密市| 寿光市| 高碑店市| 奉新县| 察雅县| 保康县| 新平| 诸暨市| 楚雄市| 兴安盟| 澄迈县| 大埔区| 静安区| 黄石市| 芒康县| 哈密市| 博野县| 多伦县| 佳木斯市| 夏津县| 襄城县| 红安县| 休宁县| 当涂县| 高邑县| 永和县| 彩票| 巴塘县| 郸城县| 莱芜市| 敦化市|