- 您現在的位置：買賣IC網 > PDF目錄98243 > TLC5618IP (TEXAS INSTRUMENTS INC) SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, PDIP8 PDF資料下載
參數資料
| 型號： | TLC5618IP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | DAC |
| 英文描述： | SERIAL INPUT LOADING, 12.5 us SETTLING TIME, 12-BIT DAC, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 10/26頁 |
| 文件大小： | 386K |
| 代理商： | TLC5618IP |
TLC5618, TLC5618A
PROGRAMMABLE DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTERS
SLAS156G – JULY 1997 – REVISED APRIL 2001
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
SCLK
DIN
CS
TLC5618,
TLC5618A
SCK
MOSI
I/O
SPI/QSPI
Port
CPOL = 1, CPHA = 0
Figure 24. SPI/QSPI Connection
linearity, offset, and gain error using single end supplies
When an amplifier is operated from a single supply, the voltage offset can still be either positive or negative. With
a positive offset, the output voltage changes on the first code change. With a negative offset the output voltage
may not change with the first code depending on the magnitude of the offset voltage.
The output amplifier attempts to drive the output to a negative voltage. However, because the most negative
supply rail is ground, the output cannot drive below ground and clamps the output at 0 V.
The output voltage then remains at zero until the input code value produces a sufficient positive output voltage
to overcome the negative offset voltage, resulting in the transfer function shown in Figure 25.
DAC Code
Output
Voltage
0 V
Negative
Offset
Figure 25. Effect of Negative Offset (Single Supply)
This offset error, not the linearity error, produces this breakpoint. The transfer function would have followed the
dotted line if the output buffer could drive below the ground rail.
For a DAC, linearity is measured between zero-input code (all inputs 0) and full-scale code (all inputs 1) after
offset and full scale are adjusted out or accounted for in some way. However, single supply operation does not
allow for adjustment when the offset is negative due to the breakpoint in the transfer function. So the linearity
is measured between full-scale code and the lowest code that produces a positive output voltage. The code is
calculated from the maximum specification for the negative offset.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC5620CN | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDIP14 |
| TLC5620CDR | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
| TLC5620IDR | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
| TLC5620CDG4 | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
| TLC5620CDRG4 | SERIAL INPUT LOADING, 10 us SETTLING TIME, 8-BIT DAC, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC5620 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUADRUPLE 8-BIT DIGITAL-TO-ANALOG CONVERTERS |
| TLC5620C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUADRUPLE 8-BIT DIGITAL-TO-ANALOG CONVERTERS |
| TLC5620CD | 功能描述:數模轉換器- DAC Quad 8bit DigitAL/AN RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TLC5620CDG4 | 功能描述:數模轉換器- DAC 8-Bit 10us Quad DAC Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TLC5620CDR | 功能描述:數模轉換器- DAC 8-Bit 10us Quad DAC Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。