- 您現在的位置：買賣IC網 > PDF目錄98251 > TLV2544CDR (TEXAS INSTRUMENTS INC) 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 PDF資料下載
參數資料
| 型號： | TLV2544CDR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | GREEN, PLASTIC, SOIC-16 |
| 文件頁數： | 11/46頁 |
| 文件大小： | 1078K |
| 代理商： | TLV2544CDR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
TLV2544, TLV2548
2.7V TO 5.5V, 12BIT, 200KSPS, 4/8CHANNEL, LOW POWER
SERIAL ANALOGTODIGITAL CONVERTERS WITH AUTOPOWERDOWN
SLAS198E FEBRUARY 1999 REVISED JUNE 2003
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
reference block equivalent circuit
INTERNAL
REF
Close = Int Ref Used
Open = Ext Ref Used
REFM (See Note A)
Sample
Convert
~50 pF
CDAC
External to the Device
10
F
Internal
Reference
Compensation
Cap
0.1
F
Decoupling
Cap
REFP
NOTES: A. If internal reference is used, tie REFM to analog ground and install a 10
F (or 4.7 F) internal reference compensation capacitor
between REFP and REFM to store the charge as shown in the figure above.
B. If external reference is used, the 10
F (internal reference compensation) capacitor is optional. REFM can be connected to external
REFM or AGND.
C. Internal reference voltage drift, due to temperature variations, is approximately
±10 mV about the nominal 2 V (typically) from 10°C
to 100
°C. The nominal value also varies approximately ±50 mV across devices.
D. Internal reference leakage during low ON time: Leakage resistance is on the order of 100 M
or more. This means the time constant
is about 1000 s with 10
F compensation capacitance. Since the REF voltage does not vary much, the reference comes up quickly
after resuming from auto power down. At power up and power down the internal reference sees a glitch of about 500
V when 2 V
internal reference is used (1 mV when 4 V internal reference is used). This glitch settles out after about 50
s.
power down
The device has three power-down modes.
autopower-down mode
The device enters the autopower-down state at the end of a conversion.
In autopower-down, the power consumption reduces to about 1 mA when an internal reference is selected. The
built-in reference is still on to allow the device to resume quickly. The resumption is fast enough (within 0.5
SCLK) for use between cycles. An active CS, FS, or CSTART resumes the device from power-down state. The
power current is 1
A when an external reference is programmed and SCLK stops.
hardware/software power-down mode
Writing 8000h to the device puts the device into a software power down state, and the entire chip (including the
built-in reference) is powered down. For a hardware power-down, the dedicated PWDN pin provides another
way to power down the device asynchronously. These two power-down modes power down the entire device
including the built-in reference to save power. The power down current is reduced to about 1
A is the SCLK
is stopped.
An active CS, FS, or CSTART restores the device. There is no time delay when an external reference is selected.
However, if an internal reference is used, it takes about 20 ms to warm up. Deselect PWDN pin to remove the
device from the hardware power-down state. This requires about 20 ms to warm up if an internal reference is
also selected.
The configuration register is not affected by any of the power down modes but the sweep operation sequence
has to be started over again. All FIFO contents are cleared by the power-down modes.
相關PDF資料 |
PDF描述 |
|---|---|
| TLV2548CDW | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2544CDG4 | 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| TLV2544CPWG4 | 4-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| TLV2548CPWG4 | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2548IDW | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV2544CDRG4 | 功能描述:模數轉換器 - ADC 12-Bit 200 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV2544CPW | 功能描述:模數轉換器 - ADC 12bit 200kSPS ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV2544CPWG4 | 功能描述:模數轉換器 - ADC 12-Bit 200 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV2544CPWR | 功能描述:模數轉換器 - ADC 12-Bit 200 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV2544CPWRG4 | 功能描述:模數轉換器 - ADC 12-Bit 200 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。