- 您現在的位置：買賣IC網 > PDF目錄98252 > TLV320AIC10I (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TLV320AIC10I |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | PLASTIC, TQFP-48 |
| 文件頁數： | 20/57頁 |
| 文件大小： | 454K |
| 代理商： | TLV320AIC10I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
3–1
3 Serial Communications
DOUT, DIN, SCLK, SXCLK, FS, and Fc are the serial communication signals. SCLK is used to perform internal
processing and data transfer for serial interface between AIC10 and DSP. In the pulse/frame FS mode, there are 256
SCLKs per sampling period (512 if there are more than 4 devices in cascade). The digital-output data for the ADC
is taken from DOUT. The digital-input data for the DAC is applied to DIN. The synchronization clock for the serial
communication data and the frame-sync is taken from SCLK. The frame-sync signal that starts the ADC and DAC
data-transfer interval is taken from FS. Primary serial communication is used for signal data transmitted from the ADC
or to the DAC. Secondary communication is used to read or write words that control both the options and the circuit
configurations of the device.
The purpose of the primary and secondary communications is to allow conversion data and control data to be
transferred across the same serial port. A primary transfer is always dedicated to conversion data. A secondary
transfer or an asynchronous communication is used to set up and/or read the register values. A primary transfer
occurs for every conversion period. A secondary transfer occurs only when requested. Secondary serial
communication can be requested either by hardware (FC terminal) or by software (D0 of primary data input to DIN).
The direct configuration mode uses pin DCSI to program control registers instantly.
3.1
Primary Serial Communication
Primary serial communication is used to transmit and receive conversion signal data. The DAC word length depends
on the states of bit D0 in control register 1. After power up or reset, the device defaults to 15-bit mode. When the DAC
word length is 15 bits, the last bit of the primary 16-bit serial communication word is a control bit used to request
secondary serial communication. In the 16-bit mode, all 16 bits of the primary-communication word are used as data
for the DAC, and the hardware terminal FC must be used to request secondary communication.
Figure 3-1 shows the timing relationship for SCLK, FS, DOUT, and DIN in a primary communication. The timing
sequence for this operation is as follows:
FS is brought low by the TLV320AIC10.
A 16-bit word is transmitted from the ADC (DOUT), and then a 16-bit word is received from the DAC (DIN).
D0
D13
D15 D14
D12 D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
SCLK
FS
DIN
D0
D13
D15 D14
D12 D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
DOUT
Figure 3–1. Primary Serial Communication Timing
相關PDF資料 |
PDF描述 |
|---|---|
| TLV320AIC10CPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC10IPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC10CGQE | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC10IGQE | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC10CGQER | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV320AIC10IGQER | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC10IPFB | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC10IPFBG4 | 功能描述:接口—CODEC 18-Bit Regstr Bus Trncvr W/3-St Otpt RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC10PFB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:General-Purpose 3V to 5.5V 16-bit 22-KSPS DSP CODEC |
| TLV320AIC11 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:General-Purpose Low-Voltage 1.1V to 3.6V/0 16-bit 22-KSPS DSP CODEC |
發布緊急采購，3分鐘左右您將得到回復。