
SWITCHING CHARACTERISTICS
(1)
www.ti.com .......................................................................................................................................................... SLLS840A – MAY 2007 – REVISED AUGUST 2007
ELECTRICAL CHARACTERISTICS (continued)
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP(1)
MAX
UNIT
RON
Switch resistance
IO = 3 mA, VO = 0.4 V
27
40
VPASS
Switch output voltage
VI = 5 V, IO = 100 A
1.9
3.6
V
STATUS AND SOURCE SELECTOR PINS
IIH
High-level digital input current
VIH = 2 V or VDD
-10
10
A
IIL
Low-level digital input current
VIL = GND or 0.8 V
-10
10
A
VOH
TTL High-level output voltage
IOH = –100 A
2.4
VDD
V
VOL
TTL Low-level output voltage
IOL = 100 A
GND
0.4
V
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP(2)
MAX
UNIT
TMDS DIFFERENTIAL PINS (Y/Z)
tPLH
Propagation delay time, low-to-high-level output
400
650
900
ps
tPHL
Propagation delay time, high-to-low-level output
400
650
900
ps
tr
Differential output signal rise time (20% - 80%)
60
80
140
ps
tf
Differential output signal fall time (20% - 80%)
60
80
140
ps
RT = 50 , PRE = 0 V
tsk(p)
Pulse skew (|tPHL – tPLH|)
(3)
6
20
ps
tsk(D)
Intra-pair differential skew, see
Figure 420
40
ps
tsk(o)
Inter-pair channel-to-channel output skew(4)
30
65
ps
tsk(pp)
Part-to-part skew
(5)
510
ps
tjit(pp)
Peak-to-peak output jitter from Yj/Zj(1) residual jitter
8
20
ps
Am/Bm(1) = 250 MHz clock,
tjit(pp)
Peak-to-peak output jitter from Yj/Zj(2:4) residual jitter
60
80
ps
Am/Bm(2:4) = 2.5 Gbps HDMI pattern
tSX
Select to switch output
50
70
ns
ten
Enable time
170
250
ns
10-mA Current source to the input
tdis
Disable time
9
15
ns
Propagation delay from SCLn to SCL_SINK or SDAn to
tpd(DDC)
8
15
ns
SDA_SINK or SDA_SINK to SDAn
tsx(DDC)
Switch time from SCLn to SCL_SINK
8
15
ns
tpd(HPD)
Propagation delay (from HPD_SINK to the active port of HPD)
14
20
ns
tsx(HPD)
Switch time from port select to the latest valid status of HPD
33
50
ns
(1)
Measurements are made with the Agilent 81250 ParBert System with a N4872A generator (600 fs tJIT(CLK), 13 ps tJIT(pp)) and a N4873A
analyzer.
(2)
All typical values are at 25
°C and with a 3.3-V supply.
(3)
tsk(p) is the magnitude of the time difference between tPLH and tPHL of a specified terminal.
(4)
tsk(o) is the magnitude of the difference in propagation delay times between any specified terminals of a sink-port bank when inputs of
the active source port are tied together.
(5)
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same source, the same supply voltages, at the same temperature, and have identical packages and test circuits.
Copyright 2007, Texas Instruments Incorporated
9