- 您現在的位置：買賣IC網 > PDF目錄382646 > TMP320C6211GGP167 (Texas Instruments, Inc.) FIXED-POINT DIGITAL SIGNAL PROCESSORS PDF資料下載
參數資料
| 型號： | TMP320C6211GGP167 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| 中文描述： | 定點數字信號處理器 |
| 文件頁數： | 35/83頁 |
| 文件大小： | 1176K |
| 代理商： | TMP320C6211GGP167 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
TMS320C6211, TMS320C6211B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS073K
AUGUST 1998
REVISED MARCH 2004
35
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
31
16
15
14
13
12
11
10
9
8
Reserved
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
PD3
PD2
PD1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
7
0
Legend:
R/W
x = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the
TMS320C6000 CPU and Instruction Set Reference Guide
(literature number SPRU189).
Figure 8. PWRD Field of the CSR Register
A delay of up to nine clock cycles may occur after the instruction that sets the PWRD bits in the CSR before the
PD mode takes effect. As best practice, NOPs should be padded after the PWRD bits are set in the CSR to account
for this delay.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where
PD1 took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine with be executed
first, then the program execution returns to the instruction where PD1 took effect. In the case with an enabled
interrupt, the GIE bit in the CSR and the NMIE bit in the interrupt enable register (IER) must also be set in order
for the interrupt service routine to execute; otherwise, execution returns to the instruction where PD1 took effect
upon PD1 mode termination by an enabled interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 20 summarizes all the power-down modes.
相關PDF資料 |
PDF描述 |
|---|---|
| TMJ320C6211GGP167 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6201GGP167 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMP320C6211GJC167 | TRIMMER, 1K |
| TMJ320C6211GJC167 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6201GJC167 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMP320C6211GGPA100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR |
| TMP320C6211GHK100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR |
| TMP320C6211GHK120 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR |
| TMP320C6211GHK167 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMP320C6211GHKA100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。