- 您現在的位置：買賣IC網 > PDF目錄98267 > TPA0102PWP (TEXAS INSTRUMENTS INC) 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 PDF資料下載
參數資料
| 型號： | TPA0102PWP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| 封裝： | GREEN, PLASTIC, HTSSOP-24 |
| 文件頁數： | 26/43頁 |
| 文件大小： | 1122K |
| 代理商： | TPA0102PWP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
TPA0102
1.5-W STEREO AUDIO POWER AMPLIFIER
SLOS166E – MARCH 1997 – REVISED MARCH 2000
32
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
SE/BTL operation
The ability of the TPA0102 to easily switch between BTL and SE modes is one of its most important cost saving
features. This feature eliminates the requirement for an additional headphone amplifier in applications where
internal stereo speakers are driven in BTL mode but external headphone or speakers must be accommodated.
Internal to the TPA0102, two separate amplifiers drive OUT+ and OUT–. The SE/BTL input (terminal 14)
controls the operation of the follower amplifier that drives LOUT– and ROUT– (terminals 10 and 15). When
SE/BTL is held low, the amplifier is on and the TPA0102 is in the BTL mode. When SE/BTL is held high, the OUT–
amplifiers are in a high output impedance state, which configures the TPA0102 as an SE driver from LOUT+
and ROUT+ (terminals 3 and 22). IDD is reduced by approximately one-half in SE mode. Control of the SE/BTL
input can be from a logic-level CMOS source or, more typically, from a resistor divider network as shown in
Figure 64.
MUX
RLINE IN
RHP IN
+
–
Bypass
SE/BTL
HP/LINE
Rm2
100 k
Rm1
100 k
VDD
COUTR
16
14
Rm3
1 k
+
–
ROUT – 15
ROUT+ 22
Left
Channel
20
21
0.1
F
Figure 64. TPA0102 Resistor Divider Network Circuit
Using a readily available 1/8-in. (3.5 mm) stereo headphone jack, the control switch is closed when no plug is
inserted. When closed the 100-k
/1-k divider pulls the SE/BTL input low. When a plug is inserted, the 1-k
resistor is disconnected and the SE/BTL input is pulled high. When the input goes high, the OUT– amplifier is
shutdown causing the speaker to mute (virtually open-circuits the speaker). The OUT+ amplifier then drives
through the output capacitor (CO) into the headphone jack.
As shown in the full feature application (Figure 63), the input MUX control can be tied to the SE/BTL input. The
benefits of doing this are described in the following input MUX operation section.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA0102PWPLE | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| TPA0102PWPR | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| TPA0102PWPRG4 | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| TPA0102PWPG4 | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| TPA0103PWPLE | 2.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA0102PWPG4 | 功能描述:音頻放大器 1.5-W STEREO AUDIO POWER AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0102PWPR | 功能描述:音頻放大器 1.5-W STEREO AUDIO POWER AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0102PWPRG4 | 功能描述:音頻放大器 1.5-W STEREO AUDIO POWER AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0103 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.75-W 3-CHANNEL STEREO AUDIO POWER AMPLIFIER |
| TPA0103EVM | 功能描述:音頻 IC 開發工具 AUDIO POWER AMP EVAL MODULE RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。