- 您現在的位置：買賣IC網 > PDF目錄98267 > TPA0112PWPG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | TPA0112PWPG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封裝： | GREEN, PLASTIC, HTSSOP-24 |
| 文件頁數： | 17/34頁 |
| 文件大小： | 655K |
| 代理商： | TPA0112PWPG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
www.ti.com
RL
CC
VO(PP)
VDD
–3 dB
fc
SINGLE-ENDED OPERATION
BTL AMPLIFIER EFFICIENCY
VL(RMS)
VO
IDD
IDD(avg)
TPA0112
SLOS204C – MAY 1999 – REVISED SEPTEMBER 2004
For example, a 68-F capacitor with an 8-
speaker would attenuate low frequencies below 293 Hz. The BTL
configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency
performance is then limited only by the input network and speaker response. Cost and PCB space are also
minimized by eliminating the bulky coupling capacitor.
Figure 45. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the Crest Factor and Thermal
Considerations section.
In SE mode (see Figure 44 and Figure 45), the load is driven from the primary amplifier output for each channel
(OUT+, terminals 21 and 4).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state and reduces the amplifier's gain to 1 V/V.
Class-AB amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across
the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sine-wave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD.
The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 46).
Figure 46. Voltage and Current Waveforms for BTL Amplifiers
24
相關PDF資料 |
PDF描述 |
|---|---|
| TPA0112PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0122PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0122PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0122PWP | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0122PWPR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA0112PWPR | 功能描述:音頻放大器 St 2W APA With Int Gain Settings RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0112PWPRG4 | 功能描述:音頻放大器 St 2W APA With Int Gain Settings RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0122 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W STEREO AUDIO POWER AMPLIFIER WITH FOUR SELECTABLE GAIN SETTINGS |
| TPA0122EVM | 功能描述:音頻 IC 開發工具 TPA0122 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA0122PWP | 功能描述:音頻放大器 2W Stereo A RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。