- 您現在的位置：買賣IC網 > PDF目錄98268 > TPA0242PWP (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | TPA0242PWP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封裝： | GREEN, PLASTIC, HTSSOP-24 |
| 文件頁數： | 20/35頁 |
| 文件大小： | 806K |
| 代理商： | TPA0242PWP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
PC-BEEP OPERATION
C
PCB w
1
2p
PCB
(100 kW)
(13)
Shutdown Modes
TPA0242
SLOS287C – NOVEMBER 1999 – REVISED SEPTEMBER 2004
The PC-BEEP input allows a system beep to be sent directly from a computer through the amplifier to the
speakers with few external components. The input is activated automatically. When the PC-BEEP input is active,
both LINEIN and HPIN inputs are deselected, and both the left and right channels are driven in BTL mode with
the signal from PC-BEEP. The gain from the PC-BEEP input to the speakers is fixed at 0.3 V/V and is
independent of the volume setting. When the PC-BEEP input is deselected, the amplifier returns to the previous
operating mode and volume setting. Furthermore, if the amplifier is in shutdown mode, activating PC-BEEP takes
the device out of shutdown, outputs the PC-BEEP signal, then returns the amplifier to shutdown mode.
The preferred input signal is a square wave or pulse train. To be accurately detected, the signal must have a
minimum of 1.5-Vpp amplitude, rise and fall times of less than 0.1 s and a minimum of eight rising edges. When
the signal is no longer detected, the amplifier returns to its previous operating mode and volume setting.
To ac-couple the PC-BEEP input, choose a coupling-capacitor value to satisfy Equation 13.
The PC-BEEP input can also be dc-coupled to avoid using this coupling capacitor. The pin normally rests at
midrail when no signal is present.
The TPA0242 employs a shutdown mode of operation designed to minimize supply current (IDD) during periods
of nonuse to conserve battery power. The SHUTDOWN input terminal should be held high during normal
operation when the amplifier is in use. Pulling SHUTDOWN low mutes the outputs and puts the amplifier in a
low-current state, with IDD = 150 A. SHUTDOWN should never be left unconnected because amplifier operation
would be unpredictable.
Table 6. HP/LINE, SE/BTL, and Shutdown Functions
INPUTS(1)
AMPLIFIER STATE
HP/LINE
SE/BTL
SHUTDOWN
INPUT
OUTPUT
X
Low
X
Mute
Low
High
Line
BTL
Low
High
Line
SE
High
Low
High
HP
BTL
High
HP
SE
(1)
Do not leave inputs unconnected.
27
相關PDF資料 |
PDF描述 |
|---|---|
| TPA0242PWPR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0242PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0242PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0243DGQR | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| TPA0243DGQ | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA0242PWPG4 | 功能描述:音頻放大器 2W Stereo RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0242PWPR | 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0242PWPRG4 | 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA0243 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE |
| TPA0243DGQ | 功能描述:音頻放大器 2W Mono Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。