- 您現在的位置：買賣IC網 > PDF目錄98269 > TPA112DR (TEXAS INSTRUMENTS INC) 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | TPA112DR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 13/29頁 |
| 文件大小： | 707K |
| 代理商： | TPA112DR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
www.ti.com
POWER SUPPLY DECOUPLING, CS
MIDRAIL VOLTAGE
_
+
VDD
R
Midrail
CBYPASS
VDD
R
Midrail
CBYPASS
TLV2460
a) Midrail Voltage Generator Using a Simple
Resistor-Divider
b) Buffered Midrail Voltage Generator to Provide
Low Output Impedance
TPA112
SLOS212E – AUGUST 1998 – REVISED JUNE 2004
APPLICATION INFORMATION (continued)
The TPA112 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to
ensure that the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power supply leads.
For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor; typically, 0.1 F, placed as close as possible to the device VDD lead, works best. For filtering
lower frequency noise signals, a larger aluminum electrolytic capacitor of 10 F or greater placed near the power
amplifier is recommended.
The TPA112 is a single-supply amplifier; so, it must be properly biased to accommodate audio signals. Normally,
the amplifier is biased at VDD/2, but it can actually be biased at any voltage between VDD and ground. However,
biasing the amplifier at a point other than VDD/2 reduces the amplifier's maximum output swing. In some
applications where the circuitry driving the TPA112 has a different midrail voltage, it might make sense to use the
same midrail voltage for the TPA112, and possibly eliminate the use of the dc-blocking capacitors.
The two concerns with the midrail voltage source are the amount of noise present and its output impedance. Any
noise present on the midrail voltage source that is not present on the audio input signal will be input to the
amplifier, and passed to the output (and increased by the gain of the circuit). Common-mode noise is cancelled
out by the differential configuration of the circuit.
The output impedance of the circuit used to generate the midrail voltage needs to be low enough so as not to be
influenced by the audio signal path. A common method of generating the midrail voltage is to form a voltage
divider from the supply to ground, with a bypass capacitor from the common node to ground. This capacitor
improves the PSRR of the circuit. However, this circuit has a limited range of output impedances; so, to achieve
low output impedances, the voltage generated by the voltage divider is fed into a unity-gain amplifier to lower the
output impedance of the circuit.
Figure 47. Midrail Voltage Generator
If a voltage step is applied to a speaker, it causes a noise pop. To reduce popping, the midrail voltage should
rise at a subsonic rate. That is, a rate less than the rise time of a 20-Hz waveform. If the voltage rises faster than
that, there is the possibility of a pop from the speaker.
Pop can also be heard in the speaker if the midrail voltage rises faster than the charge of either the input
coupling capacitor or the output coupling capacitor. If midrail rises first, the charging of the input and output
capacitors is heard in the speaker. To keep this noise as low as possible, the relationship shown in Equation 6
should be maintained.
20
相關PDF資料 |
PDF描述 |
|---|---|
| TPA112D | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA112DGN | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA112DGNR | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA112DG4 | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA112DGNG4 | 0.07 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA112DRG4 | 功能描述:音頻放大器 150mW Stereo RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA11CGPC0 | 功能描述:按鈕開關 SP MOM RND BLK ACT RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| TPA11CGPC004 | 功能描述:按鈕開關 SPST PUSHBUTTON SWITCH ROUND RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| TPA11CGPC004 | 制造商:TE Connectivity 功能描述:Pushbutton Switch |
| TPA11CGPC0FN | 制造商:TE Connectivity 功能描述:SWITCH SPST MOM |
發布緊急采購，3分鐘左右您將得到回復。