- 您現在的位置：買賣IC網 > PDF目錄98270 > TPA2005D1GQYRQ1 (TEXAS INSTRUMENTS INC) 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA PDF資料下載
參數資料
| 型號： | TPA2005D1GQYRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA |
| 文件頁數： | 7/29頁 |
| 文件大小： | 1192K |
| 代理商： | TPA2005D1GQYRQ1 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
BOARD LAYOUT
Component Location
Trace Width
MicroStar Junior BGA Layout
0,28
mm
0,38
mm
0,25
mm
SD
NC
IN+
IN
GND
VDD
Vo+
Vo
Solder Mask
Paste Mask
Copper Trace
8-Pin QFN (DRB) Layout
www.ti.com............................................................................................................................................. SLOS474B – AUGUST 2005 – REVISED DECEMBER 2008
Place all the external components very close to the TPA2005D1. The input resistors need to be very close to the
TPA2005D1 input pins so noise does not couple on the high-impedance nodes between the input resistors and
the input amplifier of the TPA2005D1. Placing the decoupling capacitor, CS, close to the TPA2005D1 is important
for the efficiency of the class-D amplifier. Any resistance or inductance in the trace between the device and the
capacitor can cause a loss in efficiency.
Make the high current traces going to pins VDD, GND, VO+ and VO– of the TPA2005D1 have a minimum width of
0,7 mm. If these traces are too thin, the TPA2005D1 performance and output power will decrease. The input
traces do not need to be wide, but do need to run side-by-side to enable common-mode noise cancellation.
Use the following MicroStar Junior BGA ball diameters:
0,25 mm diameter solder mask
0,28 mm diameter solder paste mask/stencil
0,38 mm diameter copper trace
Figure 32 shows how to lay out a board for the TPA2005D1 MicroStar Junior BGA.
Figure 32. TPA2005D1 MicroStar Junior BGA Board Layout (Top View)
Use the following land pattern for board layout with the 8-pin QFN (DRB) package. Note that the solder paste
should use a hatch pattern to fill solder paste at 50% to ensure that there is not too much solder paste under the
package.
Copyright 2005–2008, Texas Instruments Incorporated
15
Product Folder Link(s): TPA2005D1-Q1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2005D1ZQYRQ1 | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA |
| TPA2005D1GQYR | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA15 |
| TPA2005D1DRBR | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA2005D1ZQYRG1 | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA15 |
| TPA2005D1ZQYR | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2005D1-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.4-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER |
| TPA2005D1TDGNRQ1 | 功能描述:音頻放大器 1.4W Mono Fil-Free Class-D Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2005D1ZQYR | 功能描述:音頻放大器 Mono Fully Diff Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2005D1ZQYRG1 | 功能描述:音頻放大器 1.4W Mono Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2006D1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.45-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER WITH 1.8-V COMPATIBLE INPUT THRESHOLDS |
發布緊急采購，3分鐘左右您將得到回復。