- 您現在的位置：買賣IC網 > PDF目錄98270 > TPA2006D1DRBTG4 (TEXAS INSTRUMENTS INC) 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 PDF資料下載
參數資料
| 型號： | TPA2006D1DRBTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, SON-8 |
| 文件頁數： | 2/25頁 |
| 文件大小： | 1002K |
| 代理商： | TPA2006D1DRBTG4 |
Input Resistors (RI)
Gain +
2 x 150 kW
R
I
V
(1)
Decoupling Capacitor (CS)
Input Capacitors (CI)
fc +
1
2p R
I
C
I
(2)
C
I +
1
2p R
I
fc
(3)
SLOS498A – SEPTEMBER 2006 – REVISED JULY 2008 ................................................................................................................................................. www.ti.com
Resistor matching is important in fully differential amplifiers. The balance of the output on the reference voltage
depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic distortion
diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or better to
keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with 1%
matching can be used with a tolerance greater than 1%.
Place the input resistors close to the TPA2006D1 to limit noise injection on the high-impedance nodes.
For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the TPA2006D1 to operate
at its best, and keeps a high voltage at the input making the inputs less susceptible to noise.
The TPA2006D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically
1
F, placed as close as possible to the device V
DD lead works best. Placing this decoupling capacitor close to
the TPA2006D1 is important for the efficiency of the class-D amplifier, because any resistance or inductance in
the trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise
signals, a 10
F or greater capacitor placed near the audio power amplifier would also help, but it is not required
in most applications because of the high PSRR of this device.
The TPA2006D1 does not require input coupling capacitors if the design uses a differential source that is biased
from 0.5 V to VDD – 0.8 V (shown in Figure 27). If the input signal is not biased within the recommended
common-mode input range, if needing to use the input as a high pass filter (shown in Figure 28), or if using a
single-ended source (shown in Figure 29), input coupling capacitors are required.
The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the
corner frequency can be set to block low frequencies in this application.
Equation 3 is reconfigured to solve for the input coupling capacitance.
If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below, and
causes pop. Any capacitor in the audio path should have a rating of X7R or better.
For a flat low-frequency response, use large input coupling capacitors (1
F). However, in a GSM phone the
ground signal is fluctuating at 217 Hz, but the signal from the codec does not have the same 217-Hz fluctuation.
The difference between the two signals is amplified, sent to the speaker, and heard as a 217-Hz hum.
10
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2006D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2008D2PWPR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2008D2PWP | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2008D2PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2008D2PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2010D1YEFR | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2006D1EVM | 功能描述:音頻 IC 開發工具 AUD POWER AMP RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA2008D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA2008D2_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA2008D2EVM | 功能描述:音頻 IC 開發工具 TPA2008D2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA2008D2PWP | 功能描述:音頻放大器 Stereo Hi-Pwr 5-V Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。