- 您現在的位置：買賣IC網 > PDF目錄98270 > TPA2008D2PWP (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | TPA2008D2PWP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封裝： | GREEN, PLASTIC, HTSSOP-24 |
| 文件頁數： | 10/26頁 |
| 文件大小： | 691K |
| 代理商： | TPA2008D2PWP |
www.ti.com
Ci ≤ CBYP / 10
(9)
POWER SUPPLY DECOUPLING, CS
MIDRAIL BYPASS CAPACITOR, CBYP
CBYP ≥ 10 × Ci
(10)
DIFFERENTIAL INPUT
SHUTDOWN MODES
TPA2008D2
SLOS413C – JULY 2003 – REVISED MAY 2004
APPLICATION INFORMATION (continued)
A further consideration for this capacitor is the leakage path from the input source through the input network (Ci)
and the feedback network to the load. This leakage current creates a dc offset voltage at the input to the
amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage
tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the
capacitor should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely
higher than the source dc level. Note that it is important to confirm the capacitor polarity in the application.
Ci must be 10 times smaller than the bypass capacitor to reduce clicking and popping noise from power on/off
and entering and leaving shutdown. After sizing Ci for a given cutoff frequency, size the bypass capacitor to 10
times that of the input capacitor.
The TPA2008D2 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling
to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. Optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power supply leads.
For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1 F, placed as close as possible to the device VDD terminal works best. For
filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 F or greater placed near
the audio power amplifier is recommended.
The midrail bypass capacitor (CBYP) is the most critical capacitor and serves several important functions. During
start-up or recovery from shutdown mode, CBYP determines the rate at which the amplifier starts up. The second
function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This
noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and
THD+N.
Bypass capacitor (CBYP) values of 0.47-F to 1-F ceramic or tantalum low-ESR capacitors are recommended for
the best THD and noise performance.
Increasing the bypass capacitor reduces clicking and popping noise from power on/off and entering and leaving
shutdown. To have minimal pop, CBYP should be 10 times larger than Ci.
The differential input stage of the amplifier cancels any noise that appears on both input lines of the channel. To
use the TPA2008D2 EVM with a differential source, connect the positive lead of the audio source to the INP
input and the negative lead from the audio source to the INN input. To use the TPA2008D2 with a single-ended
source, ac ground either input through a capacitor and apply the audio signal to the remaining input. In a
single-ended input application, the unused input should be ac-grounded at the audio source instead of at the
device input for best noise performance.
The TPA2008D2 employs a shutdown mode of operation designed to reduce supply current (IDD) to the absolute
minimum level during periods of nonuse for battery-power conservation. The SHUTDOWN input terminal should
be held high during normal operation when the amplifier is in use. Pulling SHUTDOWN low causes the outputs to
mute and the amplifier to enter a low-current state, IDD(SD) = 1 A. SHUTDOWN should never be left
unconnected because the amplifier state would be unpredictable.
18
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2008D2PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2008D2PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA2010D1YEFR | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TPA2010D1YEFT | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TPA2010D1YZFR | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2008D2PWPG4 | 功能描述:音頻放大器 Stereo Hi-Pwr 5-V Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2008D2PWPR | 功能描述:音頻放大器 Stereo Hi-Pwr 5-V Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2008D2PWPRG4 | 功能描述:音頻放大器 Stereo Hi-Pwr 5-V Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA200RL | 功能描述:TVS 二極管 - 瞬態電壓抑制器 200V 50uA Bidirect RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| TPA2010 | 制造商:TI 功能描述:2.5-W high efficiency filter-free class-D audio power amplifier |
發布緊急采購，3分鐘左右您將得到回復。