- 您現在的位置：買賣IC網 > PDF目錄98270 > TPA2013D1RGPR (TEXAS INSTRUMENTS INC) 2.7 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 PDF資料下載
參數資料
| 型號： | TPA2013D1RGPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.7 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| 封裝： | 4 X 4 MM, GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 6/30頁 |
| 文件大小： | 949K |
| 代理商： | TPA2013D1RGPR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
SETTING THE BOOST VOLTAGE
CC
0.5
(R1 + R2)
V
=
R1
÷
è
(1)
INDUCTOR SELECTION
CC
L
CC
DD
V
I
= I
V
0.8
÷
è
(2)
DD
CC
DD
L
CC
V
(V
V
)
L =
I
f
V
boost
-
D
(3)
SLOS520 – AUGUST 2007
Use Equation 1 to determine the value of R1 for a given VCC. The maximum recommended value for VCC is
5.5 V. The typical value of the VCCFB pin is 500 mV. The current through the resistor divider should be about 100
times greater than the current into the VCCFB pin, typically 0.01 μA. Based on those two values, the
recommended value of R2 is 500 k
. VCC must be greater than 3 V and less than or equal to 5.5 V.
SURFACE MOUNT INDUCTORS
Working inductance decreases as inductor current increases. If the drop in working inductance is severe enough,
it may cause the boost converter to become unstable, or cause the TPA2013D1 to reach its current limit at a
lower output power than expected. Inductor vendors specify currents at which inductor values decrease by a
specific percentage. This can vary by 10% to 35%. Inductance is also affected by dc current and temperature.
TPA2013D1 INDUCTOR EQUATIONS
Inductor current rating is determined by the requirements of the load. The inductance is determined by two
factors: the minimum value required for stability and the maximum ripple current permitted in the application.
Use Equation 2 to determine the required current rating. Equation 2 shows the approximate relationship between
the average inductor current, IL, to the load current, load voltage, and input voltage (ICC, VCC, and VDD,
respectively). Insert ICC, VCC, and VDD into Equation 2 to solve for IL. The inductor must maintain at least 90% of
its initial inductance value at this current.
The minimum working inductance is 2.2
μH. A lower value may cause instability.
Ripple current,
ΔIL, is peak-to-peak variation in inductor current. Smaller ripple current reduces core losses in the
inductor as well as the potential for EMI. Use Equation 3 to determine the value of the inductor, L. Equation 3
shows the relationship between inductance L, VDD, VCC, the switching frequency, fboost, and ΔIL. Insert the
maximum acceptable ripple current into Equation 3 to solve for L.
ΔIL is inversely proportional to L. Minimize ΔIL as much as is necessary for a specific application. Increase the
inductance to reduce the ripple current. Note that making the inductance too large will prevent the boost
converter from responding to fast load changes properly. Typical inductor values for the TPA2013D1 are 4.7
μH
to 6.8
μH.
Select an inductor with a small dc resistance, DCR. DCR reduces the output power due to the voltage drop
across the inductor.
14
Copyright 2007, Texas Instruments Incorporated
Product Folder Link(s): TPA2013D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2013D1YZHR | 2.7 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2013D1RGP | 2.7 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2013D1RGPT | 2.7 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2013D1YZHT | 2.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2014D1YZHT | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2013D1RGPRG4 | 功能描述:音頻放大器 2.7W Constant Output Pwr Mono Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2013D1RGPT | 制造商:Texas Instruments 功能描述:AUD AMP SPKR 1CH MONO 2.7W CLS-D 20QFN - Tape and Reel |
| TPA2013D1YZH | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7-W CONSTANT OUTPUT POWER CLASS-D AUDIO AMPLIFIER WITH INTEGRATED BOOST CONVERTER |
| TPA2013D1YZHR | 功能描述:音頻放大器 2.7W OUTPUT PWR MONO CLASS-D AUD AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2013D1YZHT | 制造商:Texas Instruments 功能描述:AUD AMP SPKR 1CH MONO 2.7W CLS-D 16DSBGA - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。