- 您現在的位置：買賣IC網 > PDF目錄98271 > TPA2014D1RGPT (TEXAS INSTRUMENTS INC) 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 PDF資料下載
參數資料
| 型號： | TPA2014D1RGPT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| 封裝： | 4 X 4 MM, GREEN, PLASTIC, QFN-20 |
| 文件頁數： | 11/27頁 |
| 文件大小： | 945K |
| 代理商： | TPA2014D1RGPT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Copper TraceWidth
Solder PadWidth
SolderMask Opening
Copper Trace Thickness
SolderMask Thickness
Trace Width
www.ti.com ............................................................................................................................................................... SLAS559A – MAY 2008 – REVISED JUNE 2008
Figure 18. Land Pattern Dimensions
Table 5. Land Pattern Dimensions
SOLDER PAD
SOLDER MASK
COPPER
STENCIL
COPPER PAD
DEFINITIONS
OPENING
THICKNESS
OPENING
THICKNESS
Nonsolder mask
275
m
375
m
275
m x 275 m Sq.
1 oz max (32
m)
125
m thick
defined (NSMD)
(+0.0, –25
m)
(+0.0, –25
m)
(rounded corners)
NOTES:
1. Circuit traces from NSMD defined PWB lands should be 75
m to 100 m wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Recommend solder paste is Type 3 or Type 4.
3. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20
m on top of the copper circuit pattern.
6. Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically
etched stencils results in inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Recommended trace width at the solder balls is 75
m to 100 m to prevent solder wicking onto wider PCB
traces.
For high current pins (SW, PGND, VOUT+, VOUT–, VCCIN, and VCCOUT) of the TPA2014D1, use 100 m trace
widths at the solder balls and at least 500
m PCB traces to ensure proper performance and output power for
the device.
For low current pins (IN–, IN+, SDd, SDb, GAIN, VCCFB, VDD) of the TPA2014D1, use 75 m to 100 m trace
widths at the solder balls. Run IN- and IN+ traces side-by-side to maximize common-mode noise cancellation.
Copyright 2008, Texas Instruments Incorporated
19
Product Folder Link(s): TPA2014D1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2014D1RGPTG4 | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2014D1RGPR | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2014D1RGPRG4 | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2015D1YZHR | 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
| TPA2015D1YZHT | 1.7 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2014D1RGPTG4 | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2014D1YZHR | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2014D1YZHT | 功能描述:音頻放大器 1.5W Constant Output Pwr Class-D Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2015D1 | 制造商:TI 功能描述:2 W Constant Output Power Class-D Audio Amplifier With Adaptive Boost Converter and Battery Tracking SpeakerGuard? AGC |
| TPA2015D1_10 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2 W Constant Output Power Class-D Audio Amplifier With Adaptive Boost Converter and Battery Tracking SpeakerGuard? AGC |
發布緊急采購，3分鐘左右您將得到回復。