- 您現在的位置：買賣IC網 > PDF目錄98272 > TPA3003D2PFBG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TPA3003D2PFBG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| 封裝： | GREEN, PLASTIC, TQFP-48 |
| 文件頁數： | 14/36頁 |
| 文件大小： | 755K |
| 代理商： | TPA3003D2PFBG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
TPA3003D2
SLOS406A FEBRUARY 2003 REVISED MARCH 2003
21
www.ti.com
APPLICATION INFORMATION
GND
SD = 0 V
Figure 28. Differential Output With FADE Terminal Held High
MUTE operation
The MUTE pin is an input for controlling the output state of the TPA3003D2. A logic high on this pin disables
the outputs. A logic low on this pin enables the outputs. This pin may be used as a quick disable or enable of
the outputs without a volume fade. Quiescent current is listed in the dc characteristics specification table. The
MUTE pin should never be left floating.
For power conservation, the SD pin should be used to reduce the quiescent current to the absolute minimum
level. The volume will fade, slowly increase or decrease, when leaving or entering the shutdown state if the
FADE terminal is held low. If the FADE terminal is held high, the outputs will transition very quickly. Refer to the
FADE operation section.
SD operation
The TPA3003D2 employs a shutdown mode of operation designed to reduce supply current (ICC) to the absolute
minimum level during periods of nonuse for power conservation. The SD input terminal should be held high (see
specification table for trip point)during normal operation when the amplifier is in use. Pulling SD low causes the
outputs to mute and the amplifier to enter a low-current state. SD should never be left unconnected, because
amplifier operation would be unpredictable.
For the best power-off pop performance, the amplifier should be placed in the shutdown mode prior to removing
the power supply voltage.
selection of COSC and ROSC
The switching frequency is determined using the values of the components connected to ROSC (pin 20) and
COSC (pin 21) and may be calculated with the following equation:
fOSC = 6.6 / (ROSC * COSC)
The frequency may be varied from 225 kHz to 275 kHz by adjusting the values chosen for ROSC and COSC.
The recommended values are COSC = 220 pF, ROSC=120 k for a switching frequency of 250 kHz.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3004D2PHPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3004D2PHPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3005D2PHPR | 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TPA3005D2PHP | 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TPA3005D2PHPG4 | 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA3003D2PFBR | 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA3003D2PFBRG4 | 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA3004 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA3004D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA3004D2_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
發布緊急采購，3分鐘左右您將得到回復。