- 您現在的位置：買賣IC網 > PDF目錄98272 > TPA3003D2PFBR (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TPA3003D2PFBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| 封裝： | GREEN, PLASTIC, TQFP-48 |
| 文件頁數： | 16/36頁 |
| 文件大小： | 755K |
| 代理商： | TPA3003D2PFBR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
TPA3003D2
SLOS406A FEBRUARY 2003 REVISED MARCH 2003
23
www.ti.com
APPLICATION INFORMATION
The value of Ci is important, as it directly affects the bass (low frequency) performance of the circuit. Consider
the example where Zi is 20 k and the specification calls for a flat bass response down to 20 Hz. Equation 6
is reconfigured as equation 7.
C
i +
1
2
pZ
i fc
In this example, Ci is 0.4 F, so one would likely choose a value in the range of 0.47 F to 1 F. If the gain is
known and will be constant, use Zi to calculate Ci. Calculations for Ci should be based off the impedance at the
lowest gain step intended for use in the system. A further consideration for this capacitor is the leakage path
from the input source through the input network (Ci) and the feedback network to the load. This leakage current
creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain
applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized
capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as
the dc level there is held at 2.5 V, which is likely higher than the source dc level. Note that it is important to confirm
the capacitor polarity in the application.
power supply decoupling, CS
The TPA3003D2 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling
to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power supply leads.
For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance
(ESR) ceramic capacitor, typically 0.1
F placed as close as possible to the device VCC lead works best. For
filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10
F or greater placed near
the audio power amplifier is recommended. The 10-
F capacitor also serves as a local storage capacitor for
supplying current during large signal transients on the amplifier outputs.
BSN and BSP capacitors
The full H-bridge output stages use only NMOS transistors. They therefore require bootstrap capacitors for the
high side of each output to turn on correctly. A 10-nF ceramic capacitor, rated for at least 25 V, must be connected
from each output to its corresponding bootstrap input. Specifically, one 10-nF capacitor must be connected from
xOUTP to xBSP, and one 10-nF capacitor must be connected from xOUTN to xBSN. (See the application circuit
diagram in Figure 21.)
VCLAMP capacitors
To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, two
internal regulators clamp the gate voltage. Two 1-
F capacitors must be connected from VCLAMPL (pin 25)
and VCLAMPR (pin 36) to ground and must be rated for at least 25 V. The voltages at the VCLAMP terminals
vary with VCC and may not be used for powering any other circuitry.
internal regulated 5-V supply (AVDD)
The AVDD terminal (pin 29) is the output of an internally-generated 5-V supply, used for the oscillator,
preamplifier, and volume control circuitry. It requires a 0.1-
F to 1-F capacitor, placed very close to the pin,
to ground to keep the regulator stable. The regulator may not be used to power any external circuitry.
(7)
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3003D2PFB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3003D2PFBRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3003D2PFBG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3004D2PHPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
| TPA3004D2PHPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA3003D2PFBRG4 | 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA3004 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA3004D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA3004D2_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL |
| TPA3004D2EVM | 功能描述:音頻 IC 開發工具 TPA3004D2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。