- 您現在的位置：買賣IC網 > PDF目錄98273 > TPA3107D2PAPT (TEXAS INSTRUMENTS INC) 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 PDF資料下載
參數資料
| 型號： | TPA3107D2PAPT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| 封裝： | 10 X 10 MM, GREEN, PLASTIC, HTQFP-64 |
| 文件頁數： | 15/32頁 |
| 文件大小： | 1027K |
| 代理商： | TPA3107D2PAPT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
www.ti.com
PRINTED-CIRCUIT BOARD (PCB) LAYOUT GENERAL GUIDELINES
BASIC MEASUREMENT SYSTEM
SLOS509B – OCTOBER 2006 – REVISED JULY 2007
Because the TPA3107D2 is a class-D amplifier that switches at a high frequency, the layout of the printed-circuit
board (PCB) should be optimized according to the following guidelines for the best possible performance.
Decoupling capacitors—The high-frequency 1-μF decoupling capacitors should be placed as close to the
PVCC and AVCC terminals as possible. The VBYP capacitor, VREG capacitor, and VCLAMP capacitor
should also be placed as close to the device as possible. Large bulk power supply decoupling capacitors
should be placed near the TPA3107D2 on the PVCCL, PVCCR, and AVCC terminals.
Grounding—The AVCC decoupling capacitor, VREG capacitor, VBYP capacitor, and ROSC resistor should
each be grounded to analog ground. The PVCC decoupling capacitors and VCLAMP capacitors should each
be grounded to power ground. Analog ground and power ground should be connected at the thermal pad,
which should be used as a central ground connection or star ground for the TPA3107D2.
Output filter—The ferrite EMI filter should be placed as close to the output terminals as possible for the best
EMI performance. The LC filter should be placed close to the outputs.
For an example layout, see the TPA3107D2 Evaluation Module User Manual, (SLOU190). Both the EVM user
manual and the thermal pad application note are available on the TI Web site at http://www.ti.com.
This application note focuses on methods that use the basic equipment listed below:
Audio analyzer or spectrum analyzer
Digital multimeter (DMM)
Oscilloscope
Twisted-pair wires
Signal generator
Power resistor(s)
Linear regulated power supply
Filter components
EVM or other complete audio circuit
Figure 28 shows the block diagrams of basic measurement systems for class-AB and class-D amplifiers. A sine
wave is normally used as the input signal because it consists of the fundamental frequency only (no other
harmonics are present). An analyzer is then connected to the APA output to measure the voltage output. The
analyzer must be capable of measuring the entire audio bandwidth. A regulated dc power supply is used to
reduce the noise and distortion injected into the APA through the power pins. A System Two audio
measurement system (AP-II) (Reference 1) by Audio Precision includes the signal generator and analyzer in one
package.
The generator output and amplifier input must be ac-coupled. However, the EVMs already have the ac-coupling
capacitors, (CIN), so no additional coupling is required. The generator output impedance should be low to avoid
attenuating the test signal, and is important because the input resistance of APAs is not high. Conversely, the
analyzer-input impedance should be high. The output resistance, ROUT, of the APA is normally in the hundreds
of milliohms and can be ignored for all but the power-related calculations.
Figure 28(a) shows a class-AB amplifier system. It takes an analog signal input and produces an analog signal
output. This amplifier circuit can be directly connected to the AP-II or other analyzer input.
This is not true of the class-D amplifier system shown in Figure 28(b), which requires low-pass filters in most
cases in order to measure the audio output waveforms. This is because it takes an analog input signal and
converts it into a pulse-width modulated (PWM) output signal that is not accurately processed by some
analyzers.
22
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3107D2PAP | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TPA3107D2PAPRG4 | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TPA3107D2PAPTG4 | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TPA3107D2PAPG4 | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TPA3110D2PWPR | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA3107D2PAPTG4 | 功能描述:音頻放大器 15W Stereo Class-D Audio Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA311 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:350-mW MONO AUDIO POWER AMPLIFIER |
| TPA311_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:350-mW MONO AUDIO POWER AMPLIFIER |
| TPA3110D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-W FILTER-FREE STEREO CLASS-D AUDIO POWER AMPLIFIER with SPEAKERGUARD? |
| TPA3110D2_0911 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-W FILTER-FREE STEREO CLASS-D AUDIO POWER AMPLIFIER with SPEAKERGUARD? |
發布緊急采購，3分鐘左右您將得到回復。