- 您現在的位置：買賣IC網 > PDF目錄98274 > TPA4861DRG4 (TEXAS INSTRUMENTS INC) 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | TPA4861DRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 10/26頁 |
| 文件大小： | 623K |
| 代理商： | TPA4861DRG4 |
www.ti.com
SINGLE-ENDED OPERATION
Audio
Input
VDD
6
5
8
VO1
VO2
VDD
2
3
4
IN +
IN
BYPASS
VDD/2
CI
RI
RF
CS
CB
250-mW
External
Speaker
CSE = 0.1 F
RSE = 50
CC
+
+
Gain + *
R
F
R
I
(11)
1
C
B
25 k
v
1
C
I RI
1
R
LCC
(12)
OUTPUT COUPLING CAPACITOR, CC
f
out high +
1
2p R
L CC
(13)
TPA4861
SLOS163C – SEPTEMBER 1996 – REVISED JUNE 2004
Figure 38 is a schematic diagram of the recommended SE configuration. In SE mode configurations, the load
should be driven from the primary amplifier output (VO1, terminal 5).
Figure 38. Singled-Ended Mode
Gain is set by the RF and RI resistors and is shown in Equation 11. Because the inverting amplifier is not used to
mirror the voltage swing on the load, the factor of 2 is not included.
The phase margin of the inverting amplifier into an open circuit is not adequate to ensure stability, so a
termination load should be connected to VO2. This consists of a 50- resistor in series with a 0.1-F capacitor to
ground. It is important to avoid oscillation of the inverting output to minimize noise and power dissipation.
The output coupling capacitor required in single-supply SE mode also places additional constraints on the
selection of other components in the amplifier circuit. The rules described earlier still hold with the addition of the
following relationship:
In the typical single-supply SE configuration, an output coupling capacitor (CC) is required to block the dc bias at
the output of the amplifier thus preventing dc currents in the load. As with the input coupling capacitor, the output
coupling capacitor and impedance of the load form a high-pass filter governed by Equation 13.
The main disadvantage, from a performance standpoint, is that the load impedances are typically small, which
drives the low-frequency corner higher. Large values of CC are required to pass low frequencies into the load.
Consider the example where a CC of 68 F is chosen and loads vary from 8 , 32 , and 47 k. Table 2
summarizes the frequency response characteristics of each configuration.
18
相關PDF資料 |
PDF描述 |
|---|---|
| TPA4861Y | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, UUC8 |
| TPA5050RSARG4 | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| TPA5050RSAR | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| TPA5050RSATG4 | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| TPA5050RSAT | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA-5 | 功能描述:保險絲 TELPOWER ALARM FUSE RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| TPA-5,0-ADV | 制造商:PMK 功能描述:ADVANCED PROBE ACCESSORIES 5, 0MM 制造商:PMK 功能描述:ADVANCED PROBE ACCESSORIES 5, 0MM; Kit Contents:Probe Kit, 18 Piece; Body Diameter:5.0mm; For Use With:5mm PMK Probes; Primary Product 1:220mm Ground Lead with Crocodile Clips; Primary Product 2:Sprung Hook; Primary Product 3:Contact;RoHS Compliant: NA |
| TPA-5,0-BAS | 制造商:PMK 功能描述:BASIC PROBE ACCESSORIES 5, 0MM 制造商:PMK 功能描述:BASIC PROBE ACCESSORIES 5, 0MM; Kit Contents:Probe Kit, 4 Piece; Body Diameter:5.0mm; For Use With:5mm PMK Probes; Primary Product 1:220mm Ground Lead with Crocodile Clips; Primary Product 2:Sprung Hook; Primary Product 3:Contact ;RoHS Compliant: NA |
| TPA-5,0-L-BAS | 制造商:PMK 功能描述:BASIC PROBE ACCESSORIES 5, 0-L 制造商:PMK 功能描述:BASIC PROBE ACCESSORIES 5, 0-L; Kit Contents:Probe Kit, 4 Piece; Body Diameter:5.0mm; For Use With:5mm PMK Probes; Primary Product 1:220mm Ground Lead with Crocodile Clips; Primary Product 2:Sprung Hook; Primary Product 3:Contact ;RoHS Compliant: NA |
| TPA-50 | 功能描述:保險絲 TELPOWER ALARM FUSE RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
發布緊急采購，3分鐘左右您將得到回復。