- 您現在的位置：買賣IC網 > PDF目錄98274 > TPA6030A4PWPRG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | TPA6030A4PWPRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| 封裝： | GREEN, PLASTIC, TSSOP-28 |
| 文件頁數： | 13/32頁 |
| 文件大小： | 698K |
| 代理商： | TPA6030A4PWPRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
TPA6030A4
SLOS395B DECEMBER 2002 REVISED JANUARY 2005
www.ti.com
20
VCC
VO(PP)
CC
RL
VO(PP)
3 dB
fc
Figure 25. Single-Ended Configuration and Frequency Response
Bridge-tying the outputs in a typical computer audio, or LCD TV or multimedia LCD monitor application drastically increases
output power. For example, if an amplifier in a single-ended configuration was capable of outputting a maximum of 250 mW
for a given load with a supply voltage of 12 V, then that same amplifier would be able to output 1 W of power in a BTL
configuration with the same supply voltage and load. In addition to the increase in output power, the BTL configuration does
not suffer from the same low frequency issues that plague the single-ended configuration. In a BTL configuration, there
is no need for an output capacitor to block dc, so no unwanted filtering occurs. In addition, the BTL configuration saves
money and space, as the dc-blocking capacitors needed for single-ended operation are large and expensive. For example,
with an 8- load in SE operation, the user needs a capacitor of 995 F to obtain a lower cutoff frequency of 20 Hz. This
capacitor would be very expensive and very large.
Single-Ended Operation
Figure 25 shows a Class-AB audio power amplifier in an SE configuration. In SE mode, the load is driven from the primary
amplifier for each channel (Rout+ and Lout+, terminals 27 and 16 respectively). The amplifier switches from BTL to SE
mode when the SE/BTL pin is held high(1). This puts the negative outputs of the amplifier into a high impedance state, and
reduces the amplifier’s gain according to the voltage applied to SEDIFF and SEMAX.
SE/BTL Operation
The ability of the TPA6030A4 to easily switch between BTL and SE modes is one of its most important cost saving features.
This feature eliminates the requirement for an additional headphone amplifier in applications where internal stereo
speakers are driven in BTL mode but an external headphone must be accommodated. The follower amplifiers that drive
Rout and Lout (terminals 1 and 14) are controlled by the SE/BTL input (terminal 26). When SE/BTL is held low(1), the
amplifiers are on and the TPA6030A4 is in the BTL mode. When SE/BTL is held high(1), only the positive output amplifiers
are on. The negative outputs enter a high impedance state, which configures the TPA6030A4 as an SE driver from the
Rout+ and Lout+ outputs (terminals 27 and 16). Control of the SE/BTL input can be from a separate voltage source or, more
typically, from a resistor divider network. See Figure 26 for an example of a resistor divider network.
Using a readily available 1/8-in. (3,5 mm) stereo headphone jack, the control switch is closed when no plug is inserted.
When closed, the parallel combination of R5 and R7 (see Figure 22) pulls the SE/BTL pin low(1), causing the device to
operate in BTL mode. When a plug is inserted, the 1-k resistor is disconnected and the SE/BTL input is pulled high(1).
When the input goes high(1), the negative output amplifiers go into a state of high impedance, essentially open circuiting
the speaker. The positive output amplifiers then drive through the output capacitor (CO) into the headphone jack.
IN2/IN1 Operation
The TPA6030A4 has the ability to switch between the two input sources. Those sources are dubbed IN2 and IN1. There
is no functional difference between the two inputs. Both perform equally well with any audio signal (provided that signal
is within the specified limits set forth earlier in this document). However, only one input at a time is allowed through to the
output. IN2/IN1 (terminal 26) controls which input is allowed into the amplifier. As with SE/BTL, IN2/IN1 can be controlled
by either a separate voltage source or, more typically, from a resistor divider network. See Figure 26 for an example of a
resistor divider network.
(1) Refer to the table entiled Recommended Operating Conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6030A4PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| TPA6040A4RHBT | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
| TPA6041A4RHBRG4 | 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
| TPA6041A4RHBR | 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
| TPA6043A4RHBRG4 | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6040A4 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W STEREO AUDIO POWER AMPLIFIER WITH DirectPath STEREO HEADPHONE DRIVE AND REGULATOR |
| TPA6040A4EVM | 功能描述:音頻 IC 開發工具 TPA6040A4 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6040A4RHB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W STEREO AUDIO POWER AMPLIFIER WITH DirectPath STEREO HEADPHONE DRIVE AND REGULATOR |
| TPA6040A4RHBR | 功能描述:音頻放大器 2W Stereo Aud Pwr RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6040A4RHBRG4 | 功能描述:音頻放大器 2W St Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。