- 您現在的位置：買賣IC網 > PDF目錄98275 > TPA6047A4RHBR (TEXAS INSTRUMENTS INC) 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 PDF資料下載
參數資料
| 型號： | TPA6047A4RHBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
| 封裝： | GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 14/25頁 |
| 文件大小： | 982K |
| 代理商： | TPA6047A4RHBR |
fc
IN +
1
2p R
IN CIN
C
IN +
1
2p fc
IN RIN
or
(7)
Charge Pump Flying Capacitor and CPVSS Capacitor
Decoupling Capacitors
Midrail Bypass Capacitor, CBYPASS
Low Dropout Regulator (LDO) Description
Layout Recommendations
www.ti.com.............................................................................................................................................................................................. SLOS601 – OCTOBER 2008
If a high-pass filter with a –3-dB point of no more than 20 Hz is desired over all gain settings, the minimum
impedance would be used in the Equation 7. The minimum input impedance for TPA6047A4 is 20 k
. The
capacitor value by Equation 7 would be 0.399
F. However, this is C
IN,
and the desired value is for
C(DCINPUT-BLOCKING). Multiplying CIN by 2 yields 0.80 F, which is close to the standard capacitor value of 1 F.
Place 1-
F capacitors at each input terminal of the TPA6047A4 to complete the filter.
The charge pump flying capacitor serves to transfer charge during the generation of the negative supply voltage.
The CPVSS capacitor must be at least equal to the flying capacitor in order to allow maximum charge transfer.
Low ESR capacitors are an ideal selection, and a value of 1 F is typical. Use X5R or better cermaic material.
The TPA6047A4 is a DirectPath headphone amplifier that requires adequate power supply decoupling to
ensure that the noise and total harmonic distortion (THD) are as low as possible. To filter high-frequency
transients, spikes, and digital hash on the power line, use good low equivalent-series-resistance (ESR) ceramic
capacitors, typically 1 F. Find the smallest package possible, and place as close as possible to the device VDD
lead. Placing the decoupling capacitors close to the TPA6047A4 is important for the performance of the amplifier.
Use a 10
F or greater capacitor near the TPA6047A4 to filter lower frequency noise signals; however, the high
PSRR of the TPA6047A4 makes the 10-
F capacitor unnecessary in most applications.
The midrail bypass capacitor, C(BYPASS), has several important functions. During start-up or recovery from
shutdown mode, CBYPASS determines the rate at which the amplifier starts up. A 1-F capacitor yields a start-up
time of approximately 25 ms. CBYPASS also reduces the noise coupled into the output signal by the power supply.
This improves the power supply ripple rejection (PSRR) of the amplifier. Ceramic or polyester capacitors with low
ESR and values in the range of 0.47
F to 1 F are recommended.
The TPA6047A4 contains a 4.75-V output low dropout regulator (LDO) capable of providing 120 mA with a drop
of less than 150 mV from the 5-V supply. This can be used to power an external CODEC. A 10-
F decoupling
capacitor is recommended at the output of the LDO as well as 0.1-
F capacitor to filter high-frequency noise from
the supply line.
Solder the exposed thermal pad (metal pad on the bottom of the part) on the TPA6047A4 QFN package to a
ground pad on the PCB. Fore more information, see the land pattern drawing.
It is important to keep the TPA6047A4 external components close to the body of the amplifier to limit noise
pickup. One should lay out the differential input leads symmetrical and close together to take advantage of the
inherent common mode rejection of the TPA6047A4. The layout of the TPA6047A4 evaluation module (EVM) is a
good example of component placement and the layout files are available at www.ti.com.
Copyright 2008, Texas Instruments Incorporated
21
Product Folder Link(s): TPA6047A4
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6047A4RHB | 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC32 |
| TPA6100A2DGKG4 | 0.05 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6100A2DRG4 | 0.05 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6100A2DGKRG4 | 0.05 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6100A2DR | 0.05 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6047A4RHBRG4 | 功能描述:音頻放大器 2W Stereo Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6100A2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:50-mW Ultra-Low Voltage Audio Power Amp |
| TPA6100A2D | 功能描述:音頻放大器 Ultra Low Voltage Stereo Headphone RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6100A2D_06 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:50-mW ULTRALOW VOLTAGE STEREO HEADPHONE AUDIO POWER AMPLIFIER |
| TPA6100A2DG4 | 功能描述:音頻放大器 50mW Ultra Low-Vltg St Headphone Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。