- 您現在的位置：買賣IC網 > PDF目錄98275 > TPA6110A2DGN (TEXAS INSTRUMENTS INC) 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | TPA6110A2DGN |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 6/23頁 |
| 文件大小： | 624K |
| 代理商： | TPA6110A2DGN |
Gain + *
R
f
R
i
f
c(highpass) +
1
2p R
i
C
i
C
i +
1
2p R
i fc(highpass)
Effective Impedance +
R
fRi
R
f ) Ri
f
c(lowpass) +
1
2p R
f CF
SLOS314B
– DECEMBER 2000 – REVISED MARCH 2011
APPLICATION INFORMATION
GAIN SETTING RESISTORS, Rf and Ri
INPUT CAPACITOR, Ci
The gain for the TPA6110A2 is set by resistors Rf
In the typical application, an input capacitor, Ci, is
required to allow the amplifier to bias the input signal
to the proper dc level for optimum operation. In this
case, Ci and Ri form a high-pass filter with the corner
frequency determined in Equation 4.
(1)
Given that the TPA6110A2 is a MOS amplifier, the
(4)
input impedance is very high. Consequently input
leakage
currents
are
not
generally
a
concern.
The value of Ci directly affects the bass (low
However, noise in the circuit increases as the value
frequency) performance of the circuit. Consider the
of Rf increases. In addition, a certain range of Rf
example where Ri is 20 k and the specification calls
values is required for proper start-up operation of the
for a flat bass response down to 20 Hz. Equation 4 is
amplifier.
Considering
these
factors,
it
is
reconfigured as Equation 5.
recommended that the effective impedance seen by
the inverting node of the amplifier be set between 5
k
and 20 k. The effective impedance is calculated
using Equation 2.
(5)
In this example, Ci is 0.40 F, so one would likely
choose a value in the range of 0.47
F to 1 F. A
further consideration for this capacitor is the leakage
(2)
path from the input source through the input network
For example, if the input resistance is 20 k
and the
formed by Ri, Ci, and the feedback resistor (Rf) to the
feedback resistor is 20 k
, the gain of the amplifier is
load. This leakage current creates a dc offset voltage
-1, and the effective impedance at the inverting
at the input to the amplifier that reduces useful
terminal is 10 k
, a value within the recommended
headroom, especially in high-gain applications (gain
range.
>10). For this reason a low-leakage tantalum or
ceramic capacitor is the best choice. When polarized
For
high
performance
applications,
metal-film
capacitors are used, connect the positive side of the
resistors are recommended because they tend to
capacitor to the amplifier input in most applications.
have lower noise levels than carbon resistors. For
The dc level there is held at VDD/2—likely higher than
values of Rf above 50 k, the amplifier tends to
the source dc level. It is important to confirm the
become unstable due to a pole formed from Rf and
capacitor polarity in the application.
the inherent input capacitance of the MOS input
structure. For this reason, a small compensation
POWER SUPPLY DECOUPLING, C(S)
capacitor of approximately 5 pF should be placed in
parallel with Rf. This, in effect, creates a low-pass
The TPA6110A2 is a high-performance CMOS audio
filter network with the cutoff frequency defined by
amplifier
that
requires
adequate
power-supply
decoupling to minimize the output total harmonic
distortion
(THD).
Power-supply
decoupling
also
prevents oscillations when long lead lengths are used
between the amplifier and the speaker. The optimum
(3)
decoupling is achieved by using two capacitors of
different types that target different types of noise on
For example, if Rf is 100 k and CF is 5 pF then
the
power
supply
leads.
For
higher
frequency
fc(lowpass) is 318 kHz, which is well outside the audio
transients, spikes, or digital hash on the line, a good
range.
low
equivalent-series-resistance
(ESR)
ceramic
capacitor, typically 0.1
F, placed as close as
possible to the device VDD lead, works best. For
filtering
lower-frequency
noise
signals,
a
larger
aluminum electrolytic capacitor of 10
F or greater
placed near the power amplifier is recommended.
14
Copyright
2000–2011, Texas Instruments Incorporated
Product Folder Link(s): TPA6110A2
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6110A2DGNRG4 | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6110A2DGNG4 | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6111A2DGNR | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6111A2DGN | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA6111A2DR | 0.15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6110A2DGNG4 | 功能描述:音頻放大器 Stereo Headphone Pin Compat w/LM4881 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6110A2DGNR | 功能描述:音頻放大器 Stereo Headphone Pin Compat w/LM4881 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6110A2DGNRG4 | 功能描述:音頻放大器 Stereo Headphone Pin Compat w/LM4881 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6110A2EVM | 功能描述:音頻 IC 開發(fā)工具 TPA6110A2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6111A2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:150-mW STEREO AUDIO POWER AMPLIFIER |
發(fā)布緊急采購，3分鐘左右您將得到回復。