- 您現在的位置：買賣IC網 > PDF目錄98275 > TPA6120A2DWPG4 (TEXAS INSTRUMENTS INC) 0.08 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 PDF資料下載
參數資料
| 型號： | TPA6120A2DWPG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.08 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| 封裝： | GREEN, PLASTIC, SOP-20 |
| 文件頁數： | 6/25頁 |
| 文件大小： | 611K |
| 代理商： | TPA6120A2DWPG4 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
www.ti.com
+
RF = 1 kW
VCC+
RI = 1 kW
RO = 10 W
RL
VI
VCC
+
RF = 1 kW
VCC+
RI= 1 kW
RO = 10 W
RL
VI
VCC
VI+
RI = 1 kW
RF = 1 kW
TPA6120A2
SLOS431 – MARCH 2004
APPLICATION INFORMATION (continued)
The value of the feedback resistor should be chosen by using Figure 27 through Figure 32 as guidelines. The
gain can then be set by adjusting the input resistor. The smaller the feedback resistor, the less noise is
introduced into the system. However, smaller values move the dominant pole to higher and higher frequencies,
making the device more susceptible to oscillations. Higher feedback resistor values add more noise to the
system, but pull the dominant pole down to lower frequencies, making the device more stable. Higher impedance
loads tend to make the device more unstable. One way to combat this problem is to increase the value of the
feedback resistor. It is not recommended that the feedback resistor exceed a value of 10 k
. The typical value
for the feedback resistor for the TPA6120A2 is 1 k
. In some cases, where a high-impedance load is used along
with a relatively large gain and a capacitive load, it may be necessary to increase the value of the feedback
resistor from 1 k
to 2 k, thus adding more stability to the system. Another method to deal with oscillations is to
increase the size of RO.
CAUTION:
Do not place a capacitor in the feedback path. Doing so can cause oscillations.
Capacitance at the outputs can cause oscillations. Capacitance from some sources, such as layout, can be
minimized. Other sources, such as those from the load (e.g., the inherent capacitance in a pair of headphones),
cannot be easily minimized. In this case, adjustments to RO and/or RF may be necessary.
The series output resistor should be kept at a minimum of 10
. It is small enough so that the effect on the load
is minimal, but large enough to provide the protection necessary such that the output of the amplifier sees little
capacitance. The value can be increased to provide further isolation, up to 100
.
The series resistor, RS, should be used for two reasons:
1. It prevents the positive input pin from being exposed to capacitance from the line and source.
2. It prevents the source from seeing the input capacitance of the TPA6120A2.
The 50-
resistor was chosen because it provides ample protection without interfering in any noticeable way with
the signal. Not shown is another 50-
resistor that can be placed on the source side of R
S to ground. In that
capacity, it serves as an impedance match to any 50-
source.
Figure 25. Single-Ended Input With a Noninverting Gain of -1 V/V
Figure 26. Differential Input With a Noninverting Gain of 2 V/V
Figure 26 shows the TPA6120A2 connected with differential inputs. Differential inputs are useful because they
take the greatest advantage of the device's high CMRR. The two feedback resistor values must be kept the
same, as do the input resistor values.
14
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6130A2RTJR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQCC20 |
| TPA6130A2RTJT | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQCC20 |
| TPA6130A2YZHR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, BGA16 |
| TPA6130A2YZHT | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, BGA16 |
| TPA6130A2RTJRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6120A2DWPR | 功能描述:音頻放大器 High Fidelity Stereo Headphone Drv RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6120A2DWPRG4 | 功能描述:音頻放大器 Hi Fidelity St Head phone Driver RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6120A2EVM | 功能描述:音頻 IC 開發工具 TPA6120A2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6120A2RGYEVM | 功能描述:TPA6120A2 - Headphones, 2-Channel (Stereo) Output Class AB Audio Amplifier Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 放大器類型:AB 類 輸出類型:耳機，2-通道（立體聲） 不同負載時的最大輸出功率 x 通道數:80mW x 2 @ 600 歐姆 電壓 - 電源:10 V ~ 30 V，±5 V ~ 15 V 板類型:完全填充 使用的 IC/零件:TPA6120A2 所含物品:板 標準包裝:1 |
| TPA6120A2RGYT | 功能描述:Amplifier IC Headphones, 2-Channel (Stereo) Class AB 14-VQFN (3.5x3.5) 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:AB 類 輸出類型:耳機，2-通道（立體聲） 不同負載時的最大輸出功率 x 通道數:80mW x 2 @ 600 歐姆 電壓 - 電源:10 V ~ 30 V，±5 V ~ 15 V 特性:差分輸入，短路和熱保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:14-VQFN（3.5x3.5） 封裝/外殼:14-VFQFN 裸露焊盤 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。