- 您現在的位置：買賣IC網 > PDF目錄98276 > TPA6203A1GQVR (TEXAS INSTRUMENTS INC) 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 PDF資料下載
參數資料
| 型號： | TPA6203A1GQVR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| 封裝： | 2 X 2 MM, PLASTIC, BGA-8 |
| 文件頁數： | 3/29頁 |
| 文件大小： | 952K |
| 代理商： | TPA6203A1GQVR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Input Capacitor (CI)
Decoupling Capacitor (CS)
fc +
1
2pR
I
C
I
(2)
USING LOW-ESR CAPACITORS
–3 dB
fc
DIFFERENTIAL OUTPUT VERSUS
C
I +
1
2pR
I
fc
(3)
www.ti.com.......................................................................................................................................................... SLOS364F – MARCH 2002 – REVISED JUNE 2008
The TPA6203A1 does not require input coupling
The TPA6203A1 is a high-performance CMOS audio
capacitors if using a differential input source that is
amplifier
that
requires
adequate
power
supply
biased from 0.5 V to VDD - 0.8 V. Use 1% tolerance
decoupling to ensure the output total harmonic
or better gain-setting resistors if not using input
distortion (THD) is as low as possible. Power supply
coupling capacitors.
decoupling also prevents oscillations for long lead
lengths between the amplifier and the speaker. For
In
the
single-ended
input
application
an
input
higher frequency transients, spikes, or digital hash on
capacitor, CI, is required to allow the amplifier to bias
the line, a good low equivalent-series- resistance
the input signal to the proper dc level. In this case, CI
(ESR) ceramic capacitor, typically 0.1
F to 1 F,
and RI form a high-pass filter with the corner
placed as close as possible to the device VDD lead
frequency determined in Equation 2.
works best. For filtering lower frequency noise
signals, a 10-
F or greater capacitor placed near the
audio power amplifier also helps, but is not required
in most applications because of the high PSRR of this
device.
Low-ESR capacitors are recommended throughout
this applications section. A real (as opposed to ideal)
capacitor can be modeled simply as a resistor in
series with an ideal capacitor. The voltage drop
across this resistor minimizes the beneficial effects of
the capacitor in the circuit. The lower the equivalent
value of this resistance the more the real capacitor
behaves like an ideal capacitor.
The value of CI is important to consider as it directly
affects the bass (low frequency) performance of the
SINGLE-ENDED OUTPUT
circuit. Consider the example where RI is 10 k and
Figure 31 shows a Class-AB audio power amplifier
the specification calls for a flat bass response down
(APA)
in
a
fully
differential
configuration.
The
to 100 Hz. Equation 2 is reconfigured as Equation 3.
TPA6203A1 amplifier has differential outputs driving
both ends of the load. There are several potential
benefits to this differential drive configuration, but
initially consider power to the load. The differential
In this example, CI is 0.16 F, so one would likely
drive to the speaker means that as one side is
choose a value in the range of 0.22
F to 0.47 F. A
slewing up, the other side is slewing down, and vice
further consideration for this capacitor is the leakage
versa. This in effect doubles the voltage swing on the
path from the input source through the input network
load as compared to a ground referenced load.
(RI, CI) and the feedback resistor (RF) to the load.
Plugging 2 × VO(PP) into the power equation, where
This leakage current creates a dc offset voltage at the
voltage is squared, yields 4× the output power from
input to the amplifier that reduces useful headroom,
the same supply rail and load impedance (see
especially in high gain applications. For this reason, a
ceramic capacitor is the best choice. When polarized
capacitors are used, the positive side of the capacitor
should face the amplifier input in most applications,
as the dc level there is held at VDD/2, which is likely
higher than the source dc level. It is important to
confirm the capacitor polarity in the application.
Copyright 2002–2008, Texas Instruments Incorporated
11
Product Folder Link(s): TPA6203A1
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6203A1ZQVR | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| TPA6203A1ZQVRG1 | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| TPA6203A1DRBG4 | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
| TPA6203A1DRBRG4 | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
| TPA6203A1DRBR | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6203A1ZQVR | 功能描述:音頻放大器 Mono Fully Diff Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6203A1ZQVRG1 | 功能描述:音頻放大器 1.25W Mon,Fully Diff Class-AB Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6204A1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER |
| TPA6204A1_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER |
| TPA6204A1DGN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。